Atlantic alfea excellia duo 11 Скачать руководство пользователя страница 21

Страница: 21 / 68

2 .8 Commissioning

the refrigerating gas installation

This operation is only to be carried out by

qualified fitters in compliance with the legislation

for the handling of refrigerating fluids.

Evacuation with a calibrated vacuum pump is

essential (see appendix 1).

Do not use equipment that has previously been

used with a refrigerating fluid other than a HFC.

Remove the refrigerant circuit caps only when

building the refrigerant connections .

Unfavourable conditions:

- If the temperature outdoors is b5 and

+10°C

, a vacuum gauge must be used to check

the evacuation and use the 3 vacuum method.

(

see appendix 2

- If the temperature outdoors is below +5°C

, it is

strongly recommended to connect the gas.

2 .8 .1 Start procedure

•

Checks before connection:

Checking the gas connection (large diameter).

Connect the "Gas" connection to the outdoor unit.

Blow dry nitrogen into the "Gas" connection and

observe this end:



If water or impurities come out, use a new refrigerating

connection



Otherwise expand and immediately connect to the

Hydraulic module

Checking the liquid connection (small diameter).

-Connect the "Liquid" connection to the hydraulic unit
-

Blast with Nitrogen the entire

gas-condensor-liquid

connection

and observe the end (outdoor unit side).



If water or impurities come out, use a new refrigerating

connection



Otherwise expand and immediately connect to the

outdoor unit

APPENDIX 1
Method for calibration and control of a vacuum

pump

Check the oil level of the vacuum pump.

Connect the vacuum pump with the vacuum gauge

according to the scheme.

Empty for 3 minutes

After 3 minutes, the pump

reaches its threshold value and the vacuum gauge

needle does not move.

Compare the obtained pressure with the value

of the table. Depending on the temperature, this

pressure must be less than the value indicated in

the table.
=> If this is not the case, change the seal, the

flexible hose or the pump.

T °C

5°C<T<10°C 10°C<T<15°C

15°C < T

Pmax

- bar

- mbar

0 009

0 015

0 020

Vacuomètre

Flexible

bouché

Pompe

à vide

APPENDIX 2
Method 3 empty

Connect the high pressure flexible of the manifold

on the load orifice (gas connection). A valve must

be mounted on the flexible hose from the vacuum

pump in order to isolate it.

Empty up to the desired value (see table

appendix

Liaison...

liquide

gaz

Haute

pression

Jeu de manomètres

(manifold)

Basse

pression

Vacuomètre

Pompe à vide

) Switch off the vacuum pump, close the valve at

the end of the service hose (yellow), Connect this

hose to the pressure regulator of the Nitrogen bottle,

inject 2 bars, close the hose valve,

Liaison...

liquide

gaz

Haute

pression

Azote

Connect the flexible hose again to the vacuum

pump, switch it on and progressively open the

flexible valve hose.

Liaison...

liquide

gaz

Haute

pression

Repeat this operation at least three times.

Reminder: it is strictly prohibited to carry out

these operations with refrigerating fluid.

Outlet

hose

Vacuum

gauge

Set of pressure gauges

(manifold)

Vacuum

pump

Low

pressure

High

pressure

High

pressure

High

pressure

Nitrogen

Connection

liquid

Connection

liquid

Connection

liquid

Gas

Vacuum gauge

Vacuum pump

Installation and operating manual

1605 - EN

- 21 -

alfea hybrid duo heat pump oil low NOx CH

Содержание alfea excellia duo 11





































































Результаты поиска

Содержание alfea excellia duo 11

Отзывы:

Похожие инструкции для alfea excellia duo 11

Бренды по названию

Популярные бренды

Atlantic alfea excellia duo 11, Инструкции по установке и вводу в эксплуатацию

Результаты поиска

Содержание alfea excellia duo 11

Отзывы:

Похожие инструкции для alfea excellia duo 11

Бренды по названию

Популярные бренды