background image

1  Presentation of the equipment

1 .1  Packaging

• 1 box: Outdoor unit.
• 1 box: Hydraulic module with NOx low burner and 

 

outdoor temperature probe.

Pairing table

1 .4 

Definitions

 -Split

:  the  heat  pump  is  composed  of  two  parts  (an 

outdoor  unit  to  be  located  outdoors  and  a  Hydraulic 

module to be installed inside the home).

 -

Air/water:  the  outdoor  air  is  the  energy  source  . 

 

This energy is transmitted to the heating water by the 

heat pump 

 -

Inverter: the fan and compressor speeds are modulated 

to  suit  the  heat  requirements.  This  technology 

economises energy and permits operation with single 

phase  power  supply,  regardless  of  the  power  rating 

of the heat pump, by avoiding high current demands 

when started.

 -COP

  (coefficient  of  performance:  this  is  the  ratio 

between the energy transferred to the heating circuit 

and the electrical energy consumed.

 -

hybrid: the Hydraulic module operates with dual energy

 

(air/water heat pump and integrated oil boiler).

 -

low NOx: Burner designed to minimise the emission 

of  Nitrogen  oxides  NOx  in  the  fumes.  Generally  low 

NOx  burners  are  considered  to  be  burners  whose 

emission rate is below the most severe regulations at 

that time. This limit chnages regularly according to the 

regulations and technical progress.

Denomination : alféa hybrid duo oil low NOx flue model 

11

14 +

11 3 ph .

14 3 ph .

16 3 ph .

Nominal heating performances 

 (Outdoor T° / initial T°) - 

Heating power

     +7 °C/+35°C - under-floor heating

kW

10 30

13 50

10 60

13 25

14 89

     -7 °C/+35°C - under-floor heating

kW

10 10

11 22

9 75

13 00

13 50

     +7 °C/+45°C - LT radiators

kW

9 05

11 32

10 10

12 60

13 00

     -7 °C/+45°C - LT radiators

kW

8 33

10 41

8 66

12 50

13 00

Nominal heating performances 

 (Outdoor T° / initial T°) - 

Absorbed power

     +7 °C/+35°C - under-floor heating

kW

2 57

3 50

2 68

3 20

3 70

     -7 °C/+35°C - under-floor heating

kW

3 94

4 68

3 69

5 18

5 40

     +7 °C/+45°C - LT radiators

kW

2 82

3 69

3 01

3 81

4 00

     -7 °C/+45°C - LT radiators

kW

4 05

5 24

4 04

6 00

6 37

Coefficient of performance (COP)                              (+7 °C / + 35 °C)

4.00

3 .86

3 .95

4 .14

4.02

1 .2  Optional equipment

• 

2

nd

 circuit kit

 (ref. 073953).

 

- to connect 2 heating circuits.

• 

Ambient probe T55

 (ref. 073951) or 

 

Ambient probe radio T58

 (ref. 075313).

 

- to correct the ambient temperature.

• 

Central ambient unit T75

 (ref. 073954) or

 

Central radio ambient unit T78

 (ref. 074061).

 

- to correct the ambient temperature 

 

  and programme the PAC 

• Anti-vibration pins (ref. 523574).
• Floor s

upport in white PVC 

 (ref. 809532).

• 

Duo pool kit

 (ref. 074064).

• High flow 

circulator kit 

 (ref. 073959).

 

- for a 1 circuit heated floor installation 

 

  with a PAC model 13 and 16.

1 .3  Scope

This heat pump permits:

 

- heating in winter,

 

- the production of sanitary hot water,

 

- controlling two heating circuits *,

 

- heating the pool*.

*: These options require the use of additional kits 

 

(see § "optional equipment").

1 .5  General characteristics

Installation and operating manual

 "

1605 - EN

"

alfea hybrid duo heat pump oil low NOx CH

- 4 -

Heat pump

Outdoor unit

Hybrid duo hydraulic module 

Model

ref. export

ref 

Code

ref 

Code

alféa hybrid duo 11 single phase

522 694

WOYG112LCT

700117

MH-HD

024208

alféa hybrid duo 14 

+

 single phase

522 695

WOYG140LCT

700142

alféa hybrid duo 11 three phase

522 696

WOYK112LCT

700118

alféa hybrid duo 14 three phase

522 697

WOYK140LCT

700143

alféa hybrid duo 16 three phase

522 698

WOYK160LCT

700163

Содержание alfea excellia duo 11





































































Отзывы: