ARM ARM946E-S Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 189

background image

Programmer’s Model

Copyright © ARM Limited 2000. All rights reserved.

2-9

Bits [17:15] give the data cache associativity. Bits [5:3] give the instruction cache
associativity. Table 2-6 lists the meaning of values used for cache associativity
encoding.

The cache associativity fields in the cache type register are implementation-specific
(implementor-defined). Therefore, if the implementation has an instruction or data
cache, the associativity for that cache is set to

010

to indicate a four-way set associative

cache. If either cache is not included in a specific implementation, then the associativity
field for that cache is set to

000

to indicate that the cache is absent.

The cache base size and cache size fields are generated within the cache blocks to avoid
having to resynthesize the design for different cache sizes.

Bit 14 gives the data cache base size.

Bit 2 gives the instruction cache base size.

The base size bits are implementation-specific. If the implementation has an instruction
or data cache, the base size bit for that cache is set to 0, indicating that the cache type
parameters are valid. If either cache is not included for a specific implementation, the
relevant base size is set to 1, indicating that the cache is absent.

2.3.4

Register 0, Tightly-coupled memory size register

This is a read-only register that returns the size of the tightly-coupled instruction and
data RAMs included within the ARM946E-S.

The tightly-coupled memory size register is accessed by reading CP15 register 0 with
the

opcode_2

field set to 2. For example:

MRC p15, 0, rd, c0, c0, 2; returns tightly-coupled memory size register

Table 2-6 Cache associativity encoding

Bits [17:15] and
bits [5:3]

Associativity

000

Direct mapped

010

4

«
...
27
28
29
30
31
...
»

Содержание ARM946E-S






























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM946E-S

Бренд: National Instruments Страницы: 9

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: Salusfin Страницы: 6

neutrino series

Бренд: Xilica Audio Design Страницы: 26

Бренд: Delta Tau Страницы: 74

Бренд: Baicells Страницы: 10

Бренд: Kaptia Страницы: 14

TeleCLIENT TC7730 Series

Бренд: ETL Страницы: 83

RanaSystems 13-0010--001

Бренд: RANA Systems Страницы: 328

Бренд: SYNTEK Страницы: 41

Бренд: Comway Страницы: 20

SOUL CALIBUR II

Бренд: NAMCO Страницы: 26

Бренд: EZCast Страницы: 24

Бренд: Variscite Страницы: 17

Бренд: Paradyne Страницы: 108

Бренд: Digisol Страницы: 73

Бренд: Vivotek Страницы: 46

Бренд: NUROTRON Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды