Arkon MAGB2 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 54

Arkon MAGB2 Скачать руководство пользователя страница 15

MAGB2 User Guide

14

V1.7 2021-10-01

5. Frequency output

As an analogue output MAGB2 has one frequency output (FOUT) configurable to be flow dependent. The
output is galvanically isolated open drain with following connection. The use is mainly for calibration
purposes, can be used as flowrate indicator for PLC units.

Connection:

Recommended resistance R=1 k Ω

The output can be set to:

0) OFF

(default)

1) FREQUENCY OUT

– the output generate frequency based on actual flow. User sets the flow at 1000Hz

signal. Then the frequency is proportional to the flow. The battery current consumption is higher if you
choose this option.

2) PULSE VOLUME

–

this setting works the same way as relay output->volume pulse: the output

generates a pulse when the preset volume has passed the sensor (the pulse width can be set). The battery
current consumption is higher if you choose this option. Minimal resolution is 1ml.

6. Relay output

As  a  second  analogue  output  MAGB2  has  one  latching  relay  output  configurable  to  an  error  detection  or
flow dependent. This output is used for status or volumetric information.  The output is galvanically isolated
dry contact.
Connection:

Frequency
output
connector

RELAY
output
connector

«
...
13
14
15
16
17
...
»

Содержание MAGB2























































Отзывы:

Нет отзывов