Arkon MAGB2 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 54

Arkon MAGB2 Скачать руководство пользователя страница 11

MAGB2 User Guide

10

V1.7 2021-10-01

3. MAGB2 Transmitter Unit

The MAGB2 Transmitter unit is the main part of the flowmeter. It consists of the MAGB2 motherboard, a
graphical display, touch-buttons and transmitter housing. Through the display and with help of the buttons,
you can navigate the meter menu. The following symbols are used in this manual and on the flowmeter
display.

3.1. Main screen

Possible secondary display functions:
Total Volume

This is the total volume counter; the sum of all historical flows for a particular flowmeter. The user is not able
to zero this counter without use of the service password. Direction of flow is ignored for this counter
(negative flow is calculated the same way as positive flow).

Total + Volume

This counter is only credited when the measured medium is flowing in the chosen positive direction. In case
the flow is 0, or if it is flowing in the opposite (negative) direction, the number on the counter remains the
same.

Total - Volume

This counter works the same way as the positive volume counter, yet in the opposite direction. In case the
flow is 0, or flowing in the designated positive direction, the number on this counter will remain the same.

Aux Volume

This is a 2nd total + volume counter. It works the same as the Total + Volume counter, yet with the only
difference being that it can be reset to 0 at any time, with User Settings password.
You can cycle through these 4 indication screens by pressing the up/down buttons on the transmitter.

Unit Volume

Error Code (hex)

Measurement status

Secondary
display function

Unit Flow

Clock

Battery Status

Secondary
display

Status Icons

Actual Flow

«
...
9
10
11
12
13
...
»

Содержание MAGB2























































Отзывы:

Нет отзывов