Revised by R. Robinson
Issue AV1.13 8 June 2006
32
The digit insertion LCR feature uses the Speed Dial Codes from 150 to 199 inclusive. These are programmed
in
WARNING! UNLESS AN LCR SOFTWARE CHIP IS FITTED, THESE CODES WILL STILL BE
ABLE TO BE PROGRAMMED AS SPEED DIALS BY CUSTOMERS. THIS WILL OVER-WRITE
THE LCR DATA CAUSING PROBABLE FAILURE OF THE CALL.
The structure of the digit insert LCR code is as follows.
Items 1 to 8 are the code to be matched
Items 9 & 10 are separators (no entry)
Items 11 to 14 are the start time (HHMM)
Items 15 & 16 are separators (no entry)
Items 17 to 20 are the finish time (HHMM)
Items 21 & 22 are separators (no entry)
Items 23 to 30 are the Carrier prefix code to be inserted.
SM65 uses the Tab key to select the correct data input item positions
Example:-
If
03
is dialed, the prefix code
1456
is to be used to select Optus in lieu of Telstra as the carrier for the call
during business hours
9:00AM
to
5:00PM
.
ALL DATA MUST BE ENTERED INTO THE CORRECT ITEM POSITION!
Zone 404 Code 150 starting at Item 01
01 02 03 04 05 06 07 08
09 10
11 12 13 14
15 16
17 18 19 20
21 22
23 24 25 26 27 28 29 30
0 3
0 9 0 0
1 7 0 0
1 4 5 6
code to be
start time
finish time
code to be inserted
matched
BLANK ITEMS WHERE DATA IS NOT USED AND SEPARATORS BETWEEN DATA ENTRY POINTS.
WARNING!
IF YOU ARE USING A LAPTOP TO ALTER OR ADD TO EXISTING LCR CODES
OR SPEED DIAL CODES, YOU MUST UPLOAD ALL THE EXISTING SPEED DIALS FROM THE
SYSTEM THEN MAKE THE ALTERATIONS IN THE LAPTOP AND THEN DOWNLOAD THE
NEW DATA TO THE SYSTEM.
The system will check for a match with the dialed number in items 1 to 8 and then if a match is found, it will
check to see if the time is in the operating band (items 9 to 12 & items 15 to 18).
If 24 hour insertion is required, enter 0000 for start and finish times.
If a full match is found, the code in items 21 to 30 is inserted before the original number is dialed.
The system will check through all the entered codes looking for a match, until code 150 has been checked or a
blank entry is found.
A blank entry in any of the fields stops LCR checking for that call.
As soon as a “no match” is definite (e.g. 02 was dialed or the time is out of band) the system will step onto the
next code for checking, or if at code 150, or if a space in a code is found, it will stop the LCR checking
programme.
enables / disables the LCR function
Digit insert LCR is disabled and Toll password is disabled
= 03
CO select LCR and Toll password is disabled
Digit insert LCR is enables and Toll password is disabled
Digit insert LCR is enabled and Toll password is enabled
must not be set to 0 or only the first 50 System Speed Codes will be available.
Trunk (CO) selection LCR
This allows the system to select a group of trunks depending on the number that the extension has dialed.
The system can be programmed to select a particular CO for LCR purposes.
A group of COs can be selected instead of digit insertion.
If
=03, this will turn on the “trunk select” function and turn off the digit insertion function
A code is entered into SPD codes 150~199 (e.g. 04 for mobiles)
The SPD code is also programmed to use CO 02.
