Arctic Cat XC 450 2016 Скачать руководство пользователя

Страница: 88 / 120

KC416A

4. Tilt the sensor 60° or more to the left and right

observing the meter. The meter should read 3.0-8.0

DC volts after approximately one second in the tilted

position. If the meter readings are not as specified,

the tilt sensor is defective.

KC414A

THROTTLE POSITION SENSOR (TPS)



NOTE: Preliminary checks may be performed on

this component using the diagnostic mode on the LCD

gauge (see EFI Diagnostic System in this section)

Verifying TPS Adjustment Tool

Before using the TPS adjustment tool, verify its battery

condition. The battery used in the tool is a 9-volt battery.

To check battery condition, use a digital volt/ohmmeter

set on DC volt scale. Test between the adjustment tool

black and red jacks. Insert the red lead of the digital volt-

meter into the red jack of the adjustment tool and the

black lead of the digital voltmeter into the black jack of

the adjustment tool. The green power light of the ana-

lyzer should now be illuminated. If voltage is found

below 4.9 volts, replace the battery.



NOTE: The Test Harness must be plugged into the

analyzer for testing voltage. Always verify battery

voltage is at least 4.9 DC volts before testing TPS.

Testing

1. Remove the left-side engine cover; then disconnect

the three-wire TPS connector plug.

KC517



NOTE: Prior to testing the TPS, inspect the three-

wire plug connector on the main harness and the

three-pin plug on the TPS for contamination, broken

pins, and/or corrosion.



NOTE: If the vehicle is in warranty, removing or

adjusting the TPS will void warranty. If the TPS is

tested out of specification, the throttle body must be

replaced. If the vehicle is out of warranty, the TPS

may be adjusted.

2. Connect the TPS Multi-Analyzer Harness connector

#8 to the TPS; then connect the harness to the TPS

Analyzer Tool.

FI672

3. Using a multimeter, connect the black tester lead to

the black socket (GND) on the analyzer and the red

tester lead to the white socket (VAR); then select the

DC Voltage position. With the vehicle off, the gauge

should read 0.66-0.70 and at Wide-Open Throttle it

should read up to approximately 3.88.

FI673A

Adjusting

1. Loosen the screw securing the TPS to the throttle body.

Component data can be retrieved using the CATT II. Uti-
lize the Sensor Data screen.

Содержание XC 450 2016

























































































































Результаты поиска

Содержание XC 450 2016

Отзывы:

Похожие инструкции для XC 450 2016

Бренды по названию

Популярные бренды

Arctic Cat XC 450 2016, Руководство по обслуживанию

Результаты поиска

Содержание XC 450 2016

Отзывы:

Похожие инструкции для XC 450 2016

Бренды по названию

Популярные бренды