Arctic Cat XC 450 2016 Скачать руководство пользователя страница 77

Страница: 77 / 120

Electrical System



NOTE: Certain components and sensors can be

checked by using the EFI diagnostic system and digi-

tal gauge (see EFI Diagnostic System in this section

for more information).

TESTING ELECTRICAL COMPONENTS

All electrical tests should be made using the CATT II or

the Fluke Model 77 Multimeter. The CATT II can return

data for certain components which are identified at the

beginning of their respective sub-section. If any other

type of meter is used, readings may vary due to internal

circuitry. When troubleshooting a specific component,

always verify first that the fuse(s) are good, that the

LED(s) are good, that the connections are clean and tight,

that the battery is fully charged, and that all appropriate

switches are activated.



NOTE: For test accuracy, all tests should be made

at room temperature approximately 68° F.

The electrical connections should be checked periodi-

cally for proper function. In case of an electrical failure,

check fuses, connections (for tightness, corrosion, dam-

age), and/or bulbs.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this section.

Refer to the current Special Tools Catalog for the appro-

priate tool description.



NOTE: When indicated for use, each special tool

will be identified by its specific name, as shown in the

chart below, and capitalized.



NOTE: Special tools are available from the Arctic

Cat Service Department.

Battery



NOTE: Preliminary checks may be performed on

this component using the diagnostic mode on the LCD

gauge (see EFI Diagnostic System in this section)

After being in service, batteries require regular cleaning

and recharging in order to deliver peak performance and

maximum service life. The following procedure is rec-

ommended for cleaning and maintaining a sealed battery.

Always read and follow instructions provided with bat-

tery chargers and battery products.



NOTE: Refer to all warnings and cautions provided

with the battery or battery maintainer/charger.

Loss of battery charge may be caused by ambient tem-

perature, ignition OFF current draw, corroded terminals,

self discharge, frequent start/stops, and short engine run

times. Frequent winch usage, snowplowing, extended

low RPM operation, short trips, and high amperage

accessory usage are also reasons for battery discharge.

Maintenance Charging



NOTE: Arctic Cat recommends the use of the

CTEK Multi US 800 or the CTEK Multi US 3300 for

battery maintenance charging. Maintenance charging

is required on all batteries not used for more than two

weeks or as required by battery drain.

800E

1. When charging a battery in the vehicle, be sure the

ignition switch is in the OFF position.

2. Clean the battery terminals with a solution of baking

soda and water.



NOTE: The sealing strip should NOT be removed

and NO fluid should be added.

3. Be sure the charger and battery are in a well-venti-

lated area. Be sure the charger is unplugged from the

110-volt electrical outlet.

4. Connect the red terminal lead from the charger to the

positive terminal of the battery; then connect the

black terminal lead of the charger to the negative ter-

minal of the battery.



NOTE: Optional battery charging adapters are

available from your authorized Arctic Cat dealer to

connect directly to your vehicle from the recom-

mended chargers to simplify the maintenance

charging process. Check with your authorized Arctic

Cat dealer for proper installation of these charging

adapter connectors.

5. Plug the battery charger into a 110-volt electrical

outlet.

6. If using the CTEK Multi US 800, there are no further

buttons to push. If using the CTEK Multi US 3300,

press the Mode button (A) at the left of the charger

until the Maintenance Charge Icon (B) at the bottom

illuminates. The Normal Charge Indicator (C) should

illuminate on the upper portion of the battery charger.

Description

p/n

Fluke Model 77 Multimeter

0644-559

MaxiClips

0744-041

Timing Light

0644-296

Component data can be retrieved using the CATT II. Uti-
lize the Sensor Data screen.

Содержание XC 450 2016

























































































































Результаты поиска

Содержание XC 450 2016

Отзывы:

Бренды по названию

Популярные бренды

Arctic Cat XC 450 2016, Руководство по обслуживанию

Результаты поиска

Содержание XC 450 2016

Отзывы:

Бренды по названию

Популярные бренды