Arctic Cat XC 450 2016, Руководство по обслуживанию

Страница: 80 / 120

79
2. Connect the red tester to the orange wire; then con-
nect the black tester lead to ground.
3. The meter must show battery voltage.
 NOTE: If the meter shows no battery voltage, trou-
bleshoot the battery, fuse, or the main wiring harness.

NOTE: If the meter shows battery voltage, the main
wiring harness is good; proceed to test the switch/
component or connector.
RESISTANCE (Brakelight)
1. Remove the spade connectors from the brake switch.
2. Set the meter selector to the OHMS position.
3. Connect the red tester lead to one switch terminal;
then connect the black tester lead to the other switch
terminal.
KC274
4. When the brake pedal is depressed, the meter must
show less than 1 ohm.

NOTE: If the meter shows more than 1 ohm of resis-
tance, replace the switch.
RESISTANCE (HI Beam)
The connectors are located on the right side of the ATV
next to the PDM. To access the connector, the radiator/
electrical access panel must be removed.
 NOTE: These tests should be made on the switch
side of the connector.
1. Set the meter selector to the OHMS position.
2. Connect one tester lead to the brown/black wire; then
connect the other tester lead to the lavender wire.
3. With the dimmer switch in the HI position, the meter
must show less than 1 ohm.

NOTE: If the meter shows more than 1 ohm of resis-
tance, replace the switch.
RESISTANCE (LO Beam)
1. Connect one tester lead to the brown/black wire; then
connect the other tester lead to the white wire.
2. With the dimmer switch in the LO position, the
meter must show less than 1 ohm.

NOTE: If the meter shows more than 1 ohm of resis-
tance, replace the switch.
RESISTANCE (Engine Stop)
1. Set the meter selector to the OHMS position.
2. Connect the one lead to the brown/lavender wire;
then connect the other tester lead to the black/white
wire.
3. With the switch in the OFF position, the meter must
show an open circuit.
4. With the switch in the RUN position, the meter must
show less than 1 ohm.

NOTE: If the meter shows more than 1 ohm of resis-
tance, replace the switch.
RESISTANCE (Reverse Override)

NOTE: The handlebar control switch connectors
are a six pin and a three pin. Both must be discon-
nected for this test.
1. Set the meter selector to the OHMS position.
2. Connect one tester lead to one lavender/red wire
(three-pin connector); then connect the other tester
wire to the green/red wire on the six-pin connector.
The meter must show less than 1 ohm.
3. Depress and hold the reverse override button. The
meter must show an open circuit.

NOTE: If the meter does not show as specified,
replace the switch.
RESISTANCE (Drive Select)
The connector is the snap-lock one in front of the steering
post. To access the connector, the radiator/electrical
access panel cover must be removed.

NOTE: Resistance tests should be made with the
connector disconnected and on the switch-side of the
connector.
1. Set the meter selector to the OHMS position.
2. Connect the one tester lead to the white/green wire;
then connect the other tester lead to the black wire.
3. With the selector switch in the 2WD position, the
meter must show an open circuit.
4. With the selector switch in the 4WD position, the
meter must show less than 1 ohm.
 NOTE: If the meter does not show as specified,
replace the front drive select switch.
VOLTAGE (Drive Select)

NOTE: The battery must be connected when per-
forming voltage tests.
1. Set the meter selector to the DC Voltage position.
2. Connect the black tester lead to the negative battery
terminal.
Component data can be retrieved using the CATT II. Uti-
lize the Sensor Data screen.