background image

Horizontal downflow pleated cartridge dust collector

28

  22  LIMITATION OF LIABILITY 

  22.1 

Limitation of Liability: 

Notwithstanding anything to the contrary, in no event will the seller 

parties’ liability arising out of, or related to, the product or its parts and components, whether 

pursuant to contractual or extracontractual liability, tort or under any other theory of liability, 

exceed the price paid to seller for the product giving rise to such liability.

  22.2 

Exclusion of Consequential and Similar Damages: 

Notwithstanding anything to the contrary, in 

no event will the seller part ies be liable for any indirect, punitive, special, exemplary, incidental, 

consequential or other similar damages of any type or kind (including loss of revenue, profits, 

use or other economic advantage, damages due to product failure, work stoppage or delays in 

delivery) arising out of, or in any way connected to, the product or its use, breach of contract, 

tort (including negligence), strict liability, product liability, or otherwise, regardless of cause, 

even if the seller parties had previously been advised of the possibility of such damages or could 

have reasonably foreseen them.

 22.3 

Fire and Explosion and Acceptance of Risk: 

Customer acknowledges that improper installation 

or use of the Product may result in fire or explosion. To minimize such risks, proper installation, 

operation, and maintenance of the Product in accordance with all applicable codes, standards, laws 

and regulations is critical. Prior to installation and use, customer shall ensure that the Product meets 

the applicable codes, laws and regulations, including those related to the addition of appropriate 

fire protection systems or explosion venting. Installation shall be performed by a licensed contractor 

with experience in fire and explosion and applicable codes, laws and regulations.

 23  APPLICABILITY

  23.1 

The terms herein constitute the only warranty given by Seller with respect to the Product.  No 

other terms and conditions, whether included on a purchase order or in any other document, shall 

apply or bind the Seller with respect to the Product warranty and all such terms and conditions and 

documents are expressly disclaimed. 

  24  GOVERNING LAW

  24.1 

These warranty terms will be governed by and construed under the laws in force in the Province 

of Ontario, Canada, excluding its conflict of law rules. 

Содержание Maxiflo 10MCH4-80





























Отзывы: