Aptina MT9T111 Скачать руководство пользователя | Manualshive

Страница: 2 / 147

background image

PDF: 4749051511/Source: 7788125767

Aptina reserves the right to change products or specifications without notice.

MT9T111_DG - Rev. B 9/10 EN

2

©2007 Aptina Imaging Corporation. All rights reserved.

MT9T111: Developer Guide

Introduction to Registers

Preliminary

Introduction to Registers

This developer guide refers to various memory locations and registers that the user reads
from or writes to for altering the MT9T111 operation. Hardware registers appear as
follows and may be read or written by sending the address and data information over the
two-wire serial interface.

Figure 1:

Register Legend

Other memory locations are within the microcontroller block and may be accessed by
utilizing hardware registers from 0x098E through 0x0990 (see the MT9T111 data sheet
for further details on how to use these registers). These are denoted below:

Figure 2:

Firmware Variable Legend

The MT9T111 was designed to facilitate customizations to optimize image quality pro-
cessing. As the image data travels through the various stages of image processing, the
user can adjust the parameters in these stages to affect the images' appearances. This
section describes most of these available adjustments.

Accessing the Firmware Drivers' Variables

R0x098E is used for the memory address and R0x0990 is used for data in the address.

Write Access

A write to the indirect access data register triggers a write to the targeted memory after
the two-wire serial interface has completed the WRITE cycle.

Read Access

Data is pre-fetched once the indirect access address register is updated; therefore, the
data is available when read from the indirect access data register.

R0x3024 [4:3]

Register #

Register

Bit(s)

Indication of Register

(as opposed to driver variable)

driver.variable

Name of Firmware Driver

Name of Driver’s Variable

«
1
2
3
4
...
»

Содержание MT9T111




















































































































































Отзывы:

Нет отзывов

Похожие инструкции для MT9T111

Бренд: GDC Страницы: 64

Бренд: D-2 Incorporated Страницы: 28

Бренд: D+H Страницы: 12

Бренд: IDS Страницы: 22

Бренд: Safemate Страницы: 12

Бренд: T-up Страницы: 14

Бренд: Vaisala Страницы: 24

ORBISPHERE K1200

Бренд: Hach Страницы: 104

Бренд: Taffio Страницы: 8

Бренд: Atlas Copco Страницы: 88

Бренд: Snapper Страницы: 1

Бренд: Whispbar Страницы: 16

Бренд: Valor Fires Страницы: 12

Бренд: hepco & becker Страницы: 6

Бренд: Badabulle Страницы: 15

Бренд: Dolby Laboratories Страницы: 40

Бренд: Denso Страницы: 31

Бренд: EMX Industries, Inc. Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды