Applied Biosystems 2720 Скачать руководство пользователя страница 78

Страница: 78 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 6

Temperature non-uniformity test

3. Use the stick end of a cotton swab to coat wells L1 to L6 and R1 to R6 with

mineral oil; the wells are too small for the swab end.

4. Place the 20-µL probe assembly into well L1.

Note:

As the test progresses, move the 20-µL probe assembly to each of the test

wells (L1 to L6 and R1 to R6).

5. Thread the probe wire through the channels in the 384-well temperature

verification plate to prevent damage to the probe and lead wires.

6. Make sure the probe is connected to the digital thermometer.

7. Press and release the red button to automatically close the heated cover.

IMPORTANT!

Seat the probe properly. If the probe wire is crushed when the

heated cover closes, the probe may be damaged.

8. Power on the digital thermometer.

Refer to the instructions in your Temperature Verification Kit for details on
operating the digital thermometer, Model 4500.

Configuring the

GeneAmp

9700

1. Power on the thermal cycler. The Main menu opens.

For best results, allow the thermal cycler 15 to 30 minutes to warm up to
ambient temperature before performing the test.

2. Press

(Util).

The Utilities screen opens.

3. Press

(Diag). The Diagnostics screen opens.

4. Press

(TmpVer). The Temperature Verification screen opens.

5. Press

(TNU) to automatically configure the GeneAmp

9700 for the

temperature non-uniformity test. The TNU Performance screen opens.

Running the test

The temperature non-uniformity test uses the 20-µL probe assembly to test the
temperature uniformity of six different wells in each sample block.

Note:

If necessary, press

(Cancel) to exit the test.

Temperature Verification

Temp - Calibration Verification
TNU - Temperature Non-Uniformity

Temp

Exit

TNU

TNU Performance

Sample temp = xx.x°C Cover temp = xxx°C

Place Probe in well L1
Press Run

Run

Cancel

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды