manualshive.com logo in svg

Applied Biosystems 2720, Руководство пользователя

Поделиться
Скачать
Applied Biosystems 2720 Скачать руководство пользователя страница 118

110

Thermal Cycler Temperature Verification System For GeneAmp

® 

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

®

 System User Guide

Chapter 9

Calibration verification test

Average block temperature at the 95 °C hold

Use the following formula to calculate the average block temperature at the 95 °C 
hold:

Block Average at 95 °C = T(95) – High Offset

If the block average is more than 0.75 degrees Celsius above or below 95 °C, your 
GeneAmp

®

 9600 must be recalibrated.

For example:

If the measured temperature of well E1 is 95.2 °C, and the High Offset that is printed 
on your calibration label is –0.1, you would make the following calculation:

Block Average at 95 °C = 95.2 – (–0.1) = 95.3 °C

In this example, because 95.3 °C does not differ by ±0.75 degrees Celsius from the 
programmed target temperature, your instrument would not need to be recalibrated.

Note:

The offset is the number of degrees Celsius that the temperature of well E1 

differed from the average temperature of the block when the instrument was 
calibrated at the factory.

Average block temperature at the 40 °C hold

Use the following formula to calculate the average block temperature at the 40 °C 
hold:

Block Average at 40 °C = T(40) – Low Offset

If the block average is more than 0.75 degrees Celsius above or below 40 °C, your 
GeneAmp

®

 9600 must be recalibrated.

For example:

If the measured temperature of well E1 is 39.9 °C, and the Low Offset that is printed 
on your calibration label is +0.1, you would make the following calculation:

Block Average at 40 °C = 39.9 – (+0.1) = 39.8 °C

In this example, because 39.8 °C does not differ by ±0.75 degrees Celsius from the 
programmed target temperature, your instrument would not need to be recalibrated.

Ending the test

1. Remove the 0.2-mL probe assembly from the sample block.

2. Power off the digital thermometer, then clean off the oil.

3. Wait for the sample block to reach room temperature (~25 °C), then remove the 

9600 temperature verification frame from the sample block.

PHYSICAL INJURY HAZARD.

 Hot Surface. Use care 

when working around the heated cover and sample block to avoid being burned 
by hot components.

4. Clean the oil off the sample block.

Содержание 2720
























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды