Applied Biosystems 2720 Скачать руководство пользователя страница 45

Страница: 45 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 4

Calibration verification test

Calibration verification test

Use this test to verify the temperature calibration of a GeneAmp

9700 with a dual

96-well sample block module. The calibration verification test consists of the
following procedures, which you must perform in sequence:

Setting up the 0.2-mL probe assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the GeneAmp

9700

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Running the test

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Evaluating the results

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ending the test

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PHYSICAL INJURY HAZARD.

Hot Surface. Use care when

working around the heated cover and sample block to avoid being burned by hot
components.

Required

equipment

This test requires the 0.2-mL Sample Block Module Temperature Verification Kit

(PN 4317939), which includes:

• Cotton swabs

• Light mineral oil

• Left and right dual 96-well block temperature verification plates

• 0.2-mL probe assembly

• Model 4500 digital thermometer with a 9V battery installed

Setting up the

0.2-mL probe

assembly

1. For GeneAmp

9700 with Manual Dual 96-well Sample Block Module:

If the heated cover is in the forward position, lift the lever, then slide the heated
cover back.

For GeneAmp

9700 with Auto-Lid dual 96-Well Sample Block Module:

If the heated cover is in the forward position, lift the lever, then press the red
button to slide the heated cover back.

2. Place both dual 96-well temperature verification plates on the sample block.

The plate labeled with L1 to L6 is for the left sample block. The plate labeled
with R1 to R6 is for the right sample block. Position the plates so the angled
corners face away from you.

Note:

The plates help you locate the probes within the sample blocks.

3. Using a cotton swab, coat well R3 with mineral oil.

4. Place the 0.2-mL probe assembly into well R3.

5. Thread the probe wire through the channel in the dual 96-well temperature

verification plate to prevent damage to the probe and lead wires (see

Figure 7 on

page 36

6. Make sure the probe is connected to the digital thermometer.

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды