manualshive.com logo in svg

Applied Biosystems 2720, Руководство пользователя

Поделиться
Скачать
Applied Biosystems 2720 Скачать руководство пользователя страница 116

108

Thermal Cycler Temperature Verification System For GeneAmp

® 

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

®

 System User Guide

Chapter 9

Calibration verification test

Running the test

1. Power on the GeneAmp

®

 9600. The Main menu opens.

For best results, allow the thermal cycler 15 to 30 minutes to warm up to 
ambient temperature before performing the test.

2. Press the 

OPTION

 key three times to move the pointer to 

UTIL

, then press 

ENTER

. The Utilities menu opens.

3. Press the 

OPTION

 key twice to move the pointer to 

DIAG

, then press 

ENTER

. 

The following menu opens:

4. Press 

5

, then press 

ENTER

 to run the Verify Calibration Diagnostic Test 

(Test #5).

Note:

To ensure maximum accuracy, the temperatures of the heated cover and 

the sample block are the same in this test. This condition prevents the heated 
cover from affecting the accuracy of the probe assembly.

The temperature of the sample block and heated cover increases to 40 °C, and 
the following display opens:

This display shows the current temperature of the block cover 
(Cvr = xxC) and sample block (Blk = xx.xC).

When the temperature of the block cover is within 

±

10 °C of the sample block 

temperature, the following display opens:

This display shows the current sample block temperature (“Blk=40.0C”) and a 
clock that counts up from 0 in minutes and seconds (“Time=MM:SS”).

When the clock reaches 3 minutes, the following display opens:

5. Measure the temperature of well E1 using the digital thermometer. Record this 

temperature as T(40).

Select Function

DIR-CONFIG-DIAG-DEL

Enter Diag Test #1

REVIEW History file

Going to 40°C...

Cvr = xxC Blk = xx.xC

Wait 3 minutes

Time=MM:SS Blk=40.0C

Record Temperature
Time=MM:SS Blk=95.0C

Содержание 2720
























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды