Applied Biosystems 2720 Скачать руководство пользователя страница 49

Страница: 49 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 4

Calibration verification test

Evaluating the

results

When the GeneAmp

9700 completes the calibration verification test, one of two

screens opens. See the table below to evaluate the results.

Ending the test

1. Press

(Exit).

2. Remove the 0.2-mL probe assembly from the sample block.

3. Power off the digital thermometer, then clean off the oil.

4. Wait for the sample block to reach room temperature (~25 °C), then remove the

dual 96-well temperature verification plates from the sample block.

PHYSICAL INJURY HAZARD.

Hot Surface. Use care

when working around the heated cover and sample block to avoid being burned
by hot components.

5. Clean the oil off the sample block.

If the sample block

module...

Then the...

Is properly calibrated

Calibration Verification screen displays the following message:

Does not pass the
calibration verification
test

Calibration Verification screen displays the following message:

• If the test fails, repeat the procedure to make sure that the

thermometer was not misread or that data-entry errors
were not made.

• If the test fails again, contact Applied Biosystems Technical

Support. See

“How to obtain support” on page viii

Calibration Verification

Calibration is good

Exit

Calibration Verification

Instrument may require service.

Contact Applied Biosystems

Exit

Technical Support.

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды