Applied Biosystems 2720 Скачать руководство пользователя страница 31

Страница: 31 / 151

Thermal Cycler Temperature Verification System For GeneAmp

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

System User Guide

Chapter 3

Temperature calibration verification test

Temperature calibration verification test

Use this test to verify the temperature calibration of your GeneAmp

9700 thermal

cycler that has a 0.2-mL sample block module. The test consists of the following
procedures, which you must perform in sequence:

Setting up the 0.2-mL probe assembly

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the GeneAmp

9700

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Running the test

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Evaluating the results

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ending the test

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PHYSICAL INJURY HAZARD.

Hot Surface. Use care when

working around the heated cover and sample block to avoid being burned by hot
components.

Required

equipment

This test requires the 0.2-mL Sample Block Module Temperature Verification Kit

(PN 4317939), which includes:

• Cotton swabs

• Light mineral oil

• 9700 temperature verification frame

• 0.2-mL probe assembly

• Model 4500 digital thermometer with a 9V battery installed

Setting up the

0.2-mL probe

assembly

1. If the heated cover is in the forward position, lift the lever, then slide the heated

cover back.

2. Place the 9700 temperature verification frame on the sample block.

3. Using a cotton swab, coat well A6 with mineral oil.

4. Place the 0.2-mL probe assembly into well A6.

5. Thread the probe wire through the channel in the 9700 temperature verification

frame to prevent damage to the probe and lead wires (see

Figure 5 on page 22

6. Make sure the probe is connected to the digital thermometer.

7. Slide the heated cover forward and pull the lever down.

IMPORTANT!

Seat the probe properly and close the heated cover carefully. If

the wire is crushed when you close the heated cover, the probe can be damaged.

8. Power on the digital thermometer.

Refer to the instructions in your Temperature Verification Kit for details on
operating the digital thermometer, Model 4500.

Configuring the

GeneAmp

9700

1. Power on the thermal cycler. The Main menu opens.

For best results, allow the thermal cycler 15 to 30 minutes to warm up to
ambient temperature before performing the test.

2. Press

(Util).

The Utilities screen opens.

Содержание 2720
























































































































































Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды

Applied Biosystems 2720, Руководство пользователя

Результаты поиска

Содержание 2720

Отзывы:

Бренды по названию

Популярные бренды