manualshive.com logo in svg

Applied Biosystems 2720, Руководство пользователя

Поделиться
Скачать
Applied Biosystems 2720 Скачать руководство пользователя страница 36

28

Thermal Cycler Temperature Verification System For GeneAmp

® 

PCR Systems 2720, 9600, 9700, 9800,

and Veriti

®

 System User Guide

Chapter 3

Temperature non-uniformity test

Configuring the

GeneAmp

®

 9700

1. Power on the thermal cycler. The Main menu opens. For best results, allow the 

thermal cycler 15 to 30 minutes to warm up to ambient temperature before 
performing the test.

2. Press 

F4

 (Util).

 

The Utilities screen opens.

3. Press 

F1

 (Diag). The Diagnostics screen opens.

4. Press 

F3

 (TmpVer). The Temperature Verification screen opens.

5. Press 

F2

 (TNU). 

The thermal cycler automatically starts to configure the temperature non-
uniformity test, with the cover setpoint of 35 °C and the sample starting with the 
setpoint of 37 °C. It may take several minutes for the system to stabilize at the 
cover and sample setpoint temperatures. After the system is configured, the 
TNU Performance screen opens.

Running the test

The temperature non-uniformity test uses the 0.2-mL probe assembly to test the 
temperature uniformity of 8 different wells in the sample block.

Note:

Press 

F5

 (Cancel) if you want to exit the test.

To run the temperature non-uniformity test:

1. Place the probe into the indicated well, then press 

F1

 (Run). The temperature 

non-uniformity test for the setpoint temperature of 94 °C starts, and the TNU 
Performance screen opens with the setpoint value displayed.

Note:

The sample block increases from 37 °C to 94 °C. The sample block must 

be at 94 °C ±1.0 °C. It may take several minutes for the GeneAmp

®

 9700 

thermal cycler to stabilize at the setpoint temperature.

Temperature Verification

 

F1

F3

F4

F5

F2

Temp

TNU

TNU Performance

Sample temp = xx.x°C Cover temp = xxx°C

Place Probe in well C4
Press Run

F1

F3

F4

F5

F2

Run

Cancel

TNU Performance

Sample temp = xx.x°C Cover temp = xxx°C

Setpoint is 94°C
Sample must be within 1.0°C of setpoint

F1

F3

F4

F5

F2

Cancel

Содержание 2720
























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды