Ankom HS Скачать руководство пользователя | Manualshive

Страница: 76 / 96

background image

Operator’s Manual

pg. 76

Rev 9/20/18

Digestion Times

When you press the

Digestion Times

button the following screen will be displayed.

This diagnostic allows you to modify the times used by the computer for the digestion processes. This can be helpful when
troubleshooting or demonstrating the instrument. If you press the

Save to Permanent Memory

button, the values you entered

will be saved until you change them again by using this diagnostic. If you do not press the

Save to Permanent Memory

button,

the values you entered will be saved until power is turned off, or until you change them again by using this diagnostic.

If you start a new procedure with Digestion Times other than the official method
times, a message will be displayed on the Touch Screen Display that allows you to
reset the values. A Reset from this Warning Screen is only temporary. Use the
Digestion Times screen in Diagnostics to make the reset permanent.

Pump Tube Test

When you press the

Pump Tube Test

button on the Diagnostics screen, the following screen will be displayed.

This diagnostic tests the integrity of the tubing from the pump to the inlet valves (IDF, SDF, and Waste). When you press the

START

button, the following screen will be displayed.

All lines should be charged before test is run.
Verify that all supply containers are connected and contain
the desired fluid.

Cancel

Continue

(no line charge)

Continue

(line charge)

Pump Tube Test

START

Status

Pressure

difference

(psi)

1

2

3

4

5

6

Vacuum  xx.x
cur:   -  x.x
max:   -  x.x

1.2 ml delivery

←

AOAC 991.43/985.29/2001.03

Digestion Times

(Press button with number to change)

Amylase

Digestion Time

991.43/985.29 SDF

Precipitation Time

Protease

Digestion Time

HCl/AMG

Digestion Time

Save to

Permanent

Memory

←

(minutes)

20

30

(minutes)

30

(minutes)

(minutes)

60

Reset to official

method times

(hours)

12

2001.03 SDF

Precipitation

«
...
74
75
76
77
78
...
»

Содержание HS

































































































Отзывы:

Нет отзывов

Похожие инструкции для HS

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 16

Бренд: jenway Страницы: 18

Бренд: Vega Страницы: 20

Бренд: Vega Страницы: 16

Бренд: Vega Страницы: 2

Бренд: velocomp Страницы: 4

HF scientific AccUView LED

Бренд: Watts Страницы: 40

Бренд: Vectronics Страницы: 4

Бренд: Aqua Lung Страницы: 24

Бренд: PASCO Страницы: 4

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Бренд: Camlab Страницы: 28

AcuRev 1310 Series

Бренд: AccuEnergy Страницы: 109

DistanceMaster Compact

Бренд: LaserLiner Страницы: 14

Бренд: inbody Страницы: 36

Бренд: Tektronix Страницы: 30

WIDE ANGLE CONVERSION PORT 2

Бренд: Nauticam Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды