Ankom HS Скачать руководство пользователя | Manualshive

Страница: 24 / 96

background image

Operator’s Manual

pg. 24

Rev 9/20/18

13.2

Rinse the tin with no more than 3 ml of Distilled Water to ensure complete transfer.

13.3

Repeat steps 13.1 – 13.2 for all IDF stations.

13.4

Re-install Clamp Bar A by setting it on the locator rods. Make sure the letter is on the top of the bar and the
rubber material is facing in toward the instrument.

13.5

Press the check mark (



) button on the Touch Screen Display. The following screen will be displayed.

13.6

Make sure that all clamp bars are installed with the letter on the top of the bar and the rubber material facing in
toward the instrument. Press the check mark (



) button on the Touch Screen Display. The following screen will

be displayed.

14.

Hook the front of each SDF bag in place.

14.1

Secure the SDF filter bags in place with the hooks located on the front part of Clamp Bar C.

Hooking the bags in place will put a physical hole in the front of each SDF bag.

14.2

Press the check mark (



) button on the Touch Screen Display. If you ran a method other than 991.43 prior to this

run, the following screen will be displayed.

Front of SDF Bags hooked to clamp bar C?

←



AOAC

991.43

IDF/SDF

All remaining clamp bars installed?

←



AOAC

991.43

IDF/SDF

Hook on front part of
Clamp Bar C

«
...
22
23
24
25
26
...
»

Содержание HS

































































































Отзывы:

Нет отзывов

Похожие инструкции для HS

Бренд: Samson Страницы: 4

Бренд: WattNode Страницы: 57

Бренд: Kanomax Страницы: 31

Бренд: Hach Страницы: 196

Бренд: Daewoo Страницы: 2

HYDROMETTE BL Compact TF-IR 2

Бренд: GANN Страницы: 40

Бренд: Gamry Страницы: 16

Бренд: jablotron Страницы: 2

Бренд: La Crosse Technology Страницы: 8

Бренд: Xylem Страницы: 19

Бренд: Sage Страницы: 68

Бренд: Fluidwell Страницы: 48

Бренд: Hanna Instruments Страницы: 11

Бренд: Oakton Страницы: 26

Бренд: Hanna Instruments Страницы: 32

Бренд: NetThings Страницы: 3

Бренд: Tohnichi Страницы: 12

Бренд: F&F Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды