Ankom HS Скачать руководство пользователя | Manualshive

Страница: 75 / 96

background image

Operator’s Manual

Rev 9/20/18

pg. 75

Motor Test

When you press the

Motor Test

button on the Diagnostics screen, the following screen will be displayed.

This diagnostic allows you to test the motor at different speeds (default is 240 RPM) and directions using different amounts of
fluid. Default valve settings are Water Supply open and Waste Output open. If you want to change valve settings, before
pressing the

GO

button to start the Motor Test, press the

Set Valves

button. The following screen will be displayed.

This diagnostic also displays the maximum pressure read from the vacuum sensor during the test. The value starts at zero and
will display a value while the motor is running and when it stops. This can be used for troubleshooting.

Running the Motor Test could leave fluid in some of the lines. After running a
Motor Test, always run the Clear IDF/SDF Lines diagnostic.

Set Valves

Amylase Supply

(closed)

HCl Supply

(closed)

AMG Supply

(closed)

Protease Supply

(closed)

Water Supply

(closed)

EtOH95 Supply

(closed)

EtOH78 Supply

(closed)

Buffer Supply

(closed)

IDF Inlet

(open)

Waste

(open)

SDF Inlet

(open)

Output

Supply

Motor Test

Set Valves

GO

Motor

Direction

(FWD)

120 RPM

240 RPM

Motor Speed

10.0

Amount (ml)

Vacuum  xx.x
cur:    xx.x
max:   xx.x

←

←

«
...
73
74
75
76
77
...
»

Содержание HS

































































































Отзывы:

Нет отзывов

Похожие инструкции для HS

Бренд: PAT Страницы: 55

Бренд: PAT Страницы: 31

Бренд: Yamaha Страницы: 2

Бренд: Oldham Страницы: 43

Бренд: M-system Страницы: 13

Disklavier Mark III Series

Бренд: Yamaha Страницы: 39

Бренд: ColorLite Страницы: 68

Бренд: Keithley Страницы: 31

Бренд: Keithley Страницы: 63

Бренд: Keithley Страницы: 18

Бренд: Keithley Страницы: 73

Бренд: Tohnichi Страницы: 12

Concert Performer Series Digital Piano CP110

Бренд: Kawai Страницы: 149

Бренд: Lumel Страницы: 40

Бренд: LaserLiner Страницы: 52

Бренд: Vector Страницы: 8

Бренд: GE Страницы: 16

Бренд: SPEEDMATE Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды