Ametek Brookfield JEROME 651 Скачать руководство пользователя страница 6

Страница: 6 / 68

Customer Service 800-528-7411 or 602-470-1414

Page 6 of 68

2 WARNINGS (READ THIS BEFORE USING THE 651)

•

THE 651 IS

NOT

DESIGNED TO OPERATE IN

HAZARDOUS LOCATIONS.

•

THE 651 IS DESIGNED FOR ODOR MONITORING

OF HYDROGEN SULFIDE.

•

Read the “631-X Operation Manual” (P/N 700-0037) for specifics on the 631-X.

•

Sample intervals under 30 minutes will result in a 631-X sensor life of less than 1

year.

•

Follow local and national codes when installing the 651.

•

It is recommended to use a ground fault circuit interrupter (GFCI) on the AC power

circuit for safety in an outdoor environment.

•

Do not allow rain to get inside the enclosure.

3 631-X

•

In the 651, the 631-X used has been modified to allow remote control of the keypad.

A DB9 connector on the back panel allows the 651 to control the 631-X.

•

If the 631-X sample button is pressed, the reading is logged by the 651.

Do not use any other 631-X button.

•

For maintenance and calibration, the 631-X is easily removed from the 651. An

additional 631-X (P/N X631-0151/-0152) can be purchased to keep the 651
operating when you send in a 631-X for calibration.

•

To remove the 631-X:

➢

Disconn

ect the AC power for safety. If the 651 is left on, the “631 System Error”

occurs on the 651 when a sample is attempted. To clear the error, reset AC
power or wait for the 631-

X to stop sampling and select the 651’s SYSTEM /

RESET menu item.

➢

Loosen the 631-X nozzle and pull the elbow fitting out.

➢

Disconnect the power and data cables from the 631-X.

➢

Use a quick tug to remove the 631-X from the 651.

➢

Reverse the procedure to reinstall the 631-X.

•

When replacing the 631-X, the clips that hold the 631-X in the 651 may need

adjustment. Loosen the three (3) screws for one of the clips and adjust it, so the
631-X snaps in place. If necessary, adjust the second clip as well.

•

When the 631-X is calibrated and installed back into the 651, a new VACUSHIELD

filter (P/N 800-0065) must be installed in the 651.

•

The serial number of the new 631-X must be entered into the 651 using the

SYSTEM / ID / 631 SN menu selection at the 651.

•

The 631-

X’s battery pack is internally disconnected to lower heat generation in the

651. To use the 631-X outside of the 651, re-connect the battery pack and connect

Содержание Brookfield JEROME 651





































































Результаты поиска

Содержание Brookfield JEROME 651

Отзывы:

Похожие инструкции для Brookfield JEROME 651

Бренды по названию

Популярные бренды

Ametek Brookfield JEROME 651, Руководство по эксплуатации

Результаты поиска

Содержание Brookfield JEROME 651

Отзывы:

Похожие инструкции для Brookfield JEROME 651

Бренды по названию

Популярные бренды