American Megatrends Excalibur PCI Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 102

background image

Chapter 3 Specifications

14

Specifications,

Continued

System BIOS

The system BIOS resides on a 128 KB boot block flash EPROM and supports shadowing between F0000h and

FFFFFh in 64 KB granularity. The system BIOS can be updated through the AMIFlash software utility. The system BIOS
is always shadowed to RAM and can be cached. The system BIOS supports the Plug and Play BIOS extensions and IDE
LBA (Logical Block Address) mode. IDE LBA mode permits IDE drives with capacities greater than 528 MB to be used.

Adaptor ROM BIOS

The Adaptor ROM BIOS between C0000h - EFFFFh can be shadowed to RAM. The contents can be read from or

written to secondary cache memory and the contents can be write-protected with 16 KB granularity via AMIBIOS Setup.

ISA Expansion Slots and Bus Speed

The Excalibur PCI motherboard has four ISA expansion slots operating at 7.5 MHz.

Mouse

The Excalibur PCI motherboard supports a PS/2- compatible mouse interface through a 10-pin dual-inline connector.

Keyboard

The standard Excalibur PCI motherboard has a five-pin DIN keyboard connector.

Green PC Monitor Connector

The Excalibur PCI motherboard has a 10-pin dual-inline connector for Green PC monitor support.

«
...
12
13
14
15
16
...
»

Содержание Excalibur PCI







































































































Отзывы:

Нет отзывов

Похожие инструкции для Excalibur PCI

Бренд: Kaba Страницы: 16

Бренд: JETWAY Страницы: 48

Бренд: Gigabyte Страницы: 104

Бренд: Renesas Страницы: 2

Бренд: ON Semiconductor Страницы: 5

Бренд: NavSpark Страницы: 18

Бренд: ASROCK Страницы: 153

Worcester TDS 300

Бренд: Bosch Страницы: 84

Бренд: Bosch Страницы: 4

Бренд: HP Страницы: 25

EVAL-AD7175-8SDZ

Бренд: Analog Devices Страницы: 11

Бренд: Analog Devices Страницы: 32

Бренд: Abit Страницы: 90

Бренд: Supermicro Страницы: 121

Бренд: Supermicro Страницы: 20

Бренд: Supermicro Страницы: 170

SuperServer 5013C-M8

Бренд: Supermicro Страницы: 94

Бренд: Supermicro Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды