American Megatrends Excalibur PCI Скачать руководство пользователя страница 78

Страница: 78 / 102

Chapter 6 WinBIOS Setup

Peripheral Setup,

Continued

On-Board Floppy Drive

This option enables the use of the floppy drive controller on the motherboard (if installed). The settings are

Enabled

Disabled.

On-Board IDE Drive

This option enables the use of the IDE controller on the motherboard (if installed). The settings are

Enabled

Disabled.

First Serial Port Address

IRQ4 is used for the first serial port (COM1). This option enables serial port 1 on the motherboard (if installed). The
settings are

2E8h.

Second Serial Port Address

IRQ3 is used for the second serial port (COM2). This option enables serial port 2 on the motherboard, if installed. The
settings are

2E8h

Parallel Port Address

IRQ7 is used for the parallel port (LPT1). The IRQ can be changed to IRQ5. This option enables the parallel port on
the motherboard, if installed. The settings are

278h

IRQ Active State

This option specifies if the parallel and serial port IRQs are active high or active low. The settings are

Low

High.

Parallel Port Mode

This option specifies the parallel port Mode. The settings are

Normal

Extended.

Содержание Excalibur PCI







































































































Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды

American Megatrends Excalibur PCI, Руководство пользователя

Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды