American Megatrends Excalibur PCI Скачать руководство пользователя страница 56

Страница: 56 / 102

AMIBIOS Displayed Error Messages,

Continued

Chapter 5 AMIBIOS POST

Error Message

Explanation

INTR #1 Error

Interrupt channel #1 has failed POST.

INTR #2 Error

Interrupt channel #2 has failed POST.

Invalid Boot
Diskette

AMIBIOS can read the diskette in floppy drive A:, but it
cannot boot the system with it. Use another boot diskette and
follow the screen instructions.

Keyboard Is
Locked...Unlock It

The keyboard lock on the system is engaged. The system
must be unlocked to continue the boot process.

Keyboard Error

Timing problem with the keyboard. Make sure a keyboard
controller AMIBIOS is installed. Set the

Keyboard

option in

STANDARD CMOS SETUP to

Not Installed

to skip the

keyboard POST routines.

KB/Interface Error

Error in the keyboard connector on the motherboard.

No ROM BASIC

Cannot find a proper bootable sector on either diskette drive
A: or hard disk drive C:. Use a bootable disk.

Off Board Parity
Error

Parity error in offboard memory. The format is:

OFF BOARD PARITY ERROR ADDR (HEX) = (XXXX)

XXXX

is the hex address where the error occurred. Run

AMIDiag to find and correct memory problems.

Onboard Parity
Error

Parity error in motherboard memory. The format is:

Onboard PARITY ERROR ADDR (HEX) = (XXXX)

XXXX

is the hex address where the error occurred. Run

AMIDiag to find and correct memory problems.

Parity Error ????

Parity error in system memory at an unknown address. Run
AMIDiag to find and correct memory problems.

Содержание Excalibur PCI







































































































Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды

American Megatrends Excalibur PCI, Руководство пользователя

Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды