American Megatrends Excalibur PCI Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 102

background image

Chapter 4 Installation

38

Step 3 Install the Motherboard

The mounting hole pattern on the motherboard is the same as the mounting hole pattern on most Baby AT-size boards.

Standoffs and mounting screws are not supplied.

Step

Action

1

Wear an anti-static wristband when performing this procedure.

2

Place the chassis on an anti-static mat. Connect the chassis to ground to avoid static damage during
installation. Connect an alligator clip with a wire lead to any unpainted part of the chassis. Ground
the other end of the lead to the same place that the mat and the wristband you are wearing are
grounded to.

3

Rotate the chassis so that the front is to the right and the rear is to the left. Mount the motherboard
on the side facing you. The power supply is mounted at the far end of the chassis.

4

Push four nylon standoffs from the solder side of the motherboard into the holes provided for them.
The standoffs lock in place. Find the slots provided for the standoffs on the chassis. Hold the
motherboard, component-side up, with the edge with the standoffs toward you and the edge with
the power supply connector away from you. The edge connectors for the adapter cards should be to
the left.

5

Carefully slide the motherboard into the chassis. Make sure that the standoffs fit the standoff slots.
The motherboard should not slide if the standoffs are properly locked. The motherboard should also
rest level with the chassis. The far edge should fit the slots in the plastic clips.

6

Place the two mounting screws in the proper holes and tighten. If necessary, shift the motherboard
slightly to align the mounting holes on the motherboard with the holes on the chassis. See page 19
and the top of this page.

The computer case manufacturer may supply installation instructions. If so, follow those procedures as well as the above procedures.

«
...
28
29
30
31
32
...
»

Содержание Excalibur PCI







































































































Отзывы:

Нет отзывов

Похожие инструкции для Excalibur PCI

Бренд: Acconeer Страницы: 14

Бренд: Biostar Страницы: 27

Бренд: ablelogic Страницы: 47

Бренд: MSI Страницы: 69

Бренд: JETWAY Страницы: 48

Cypress MB39C502-EVBSK-01

Бренд: Infineon Technologies Страницы: 28

MAG Z490 TOMAHAWK

Бренд: MSI Страницы: 76

Бренд: Diamond Systems Страницы: 112

Бренд: EPOX Страницы: 84

Бренд: ASROCK Страницы: 56

K8T8AS - REV 3.0

Бренд: JETWAY Страницы: 26

FRDMDUALK3664EVB

Бренд: NXP Semiconductors Страницы: 17

Бренд: Supermicro Страницы: 126

X58A-GD65 series

Бренд: MSI Страницы: 100

Бренд: Lenovo Страницы: 51

cPCI-6910 Series

Бренд: ADLINK Technology Страницы: 142

Бренд: Microsemi Страницы: 19

Бренд: Microsemi Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды