American Megatrends Excalibur PCI Скачать руководство пользователя страница 23

Страница: 23 / 102

Excalibur PCI Pentium ISA Motherboard User's Guide

Step 1 Set Switches and Jumpers,

Continued

J5 Select Enhanced Parallel Port DMA Acknowledge

J3 is a three-pin header that selects the parallel port DMA Acknowledge line.

J3 Pin Setting

DMA Channel

Short Pins 1-2

DACK1

Short Pins 2-3

DACK3

(Factory setting)

J4 Password LED Select

J4 is a three-pin berg that selects the Password LED.

The end user must enter the correct system password if the Password LED is blinking. If the password LED blinks,

the system has experienced no system activity during the length of time specified in Power Management Setup.

The AMIBIOS system password feature and AMIBIOS Power Management feature must be enabled before the

Password LED will blink when the correct system password must be entered by the end user.

J4 Pin Settings

LED selected

Short Pins 1-2

Front panel power LED is Password

LED.

(Factory setting)

Short Pins 2-3

Separate Password LED using P32

Содержание Excalibur PCI







































































































Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды

American Megatrends Excalibur PCI, Руководство пользователя

Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды