American Megatrends Excalibur PCI Скачать руководство пользователя страница 91

Страница: 91 / 102

Excalibur PCI Pentium ISA Motherboard User's Guide

Reprogramming from System Boot,

Continued

Sequence of Operation

The following table lists the sequence of operation and the expected behavior of the AMIFlash Code.

Step

Expected behavior

1 Look for floppy disk.

The system beeps one time before the BIOS attempts to
read from floppy drive A:.

2 Look for S701P.ROM
on the floppy disk.

S701P.ROM must be in the root directory of the floppy
disk in drive A:. There is no beep if successful.

3 Read the floppy disk.

The floppy disk is read. There is no beep if this step is
successful.

4 Check for BIOS file
size.

The BIOS file size is checked. There is no beep if this
step is successful.

5 Check for Flash
EPROM.

The BIOS looks for an Intel i28F001BX-T Flash
EPROM. It does not beep if this step is successful.

6 Erase the Flash
EPROM.

Two beeps sound when the BIOS begins erasing the
Flash EPROM.

7 Program the Flash
EPROM.

Three beeps sound when the AMIFlash Code begins
reprogramming the Flash EPROM.

8 Continue programming
the Flash EPROM.

Four beeps sound when reprogramming has been
successfully completed.

9 AMIFlash does a reset.

A CPU reset is generated (the system reboots).

10 Reboot

Reboot the system.

Содержание Excalibur PCI







































































































Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды

American Megatrends Excalibur PCI, Руководство пользователя

Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды