American Megatrends Excalibur PCI Скачать руководство пользователя страница 72

Страница: 72 / 102

Chapter 6 WinBIOS Setup

Advanced Setup,

Continued

Password Checking

This option enables the password check option every time the system boots or the end user runs Setup. If

Always

chosen, a user password prompt appears every time the computer is turned on. If

Setup

is chosen, the password prompt

appears if WinBIOS is executed. See page 79 for instructions on changing a password. The Optimal and Power-On
defaults are

Setup.

Video ROM Shadow C000,32K

When this option is set to

Enabled,

the video ROM area from C0000h - C7FFFh is copied (shadowed) to RAM for

faster execution. The settings are

Absent, NoShadow,

Shadow.

ISA Adaptor ROM at C800,16K
ISA Adaptor ROM at CC00,16K
ISA Adaptor ROM at D000,16K
ISA Adaptor ROM at D400,16K
ISA Adaptor ROM at D800,16K
ISA Adaptor ROM at DC00,16K

These options enable shadowing of the contents of the ISA Adaptor ROM area named in the option title. The settings
are

Absent, NoShadow,

Shadow.

The ROM area that is set to

Absent

will be allocated to PCI adapter cards.

Содержание Excalibur PCI







































































































Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды

American Megatrends Excalibur PCI, Руководство пользователя

Результаты поиска

Содержание Excalibur PCI

Отзывы:

Похожие инструкции для Excalibur PCI

Бренды по названию

Популярные бренды