American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 9

Страница: 9 / 65

7. A program

should be

established for the inspection and cleaning of lint in the heating unit area, exhaust

ductwork, and inside the dryer. The frequency of inspection and cleaning can best be determined from

experience at each location.

WARNING:

The collection of lint in the burner area and exhaust ductwork can create a potential fire

hazard.

8. For personal safety, the dryer

must be

electrically grounded in accordance with local codes and/or the

National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in Canada, the Canadian Electrical

Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.

NOTE

: Failure to do so will VOID THE WARRANTY.

UNDER NO CIRCUMSTANCES

should the dryer door switches, lint door switch, heat safety circuit

ever be disabled.

WARNING: PERSONAL INJURY or FIRE COULD RESULT.

10. This dryer is not to be used in the presence of dry cleaning solvents or fumes.

11. Remove articles from the dryer as soon as the drying cycle has been completed.

WARNING:

Articles left in the dryer after the drying and cooling cycles have been completed can

create a fire hazard.

12.

DO NOT

operate steam dryers with more than 125 PSI (8.62 bars) steam pressure. Excessive steam

pressure can damage steam coil and/or harm personnel.

13. Replace leaking flexible hoses or other steam fixtures immediately.

DO NOT

operate the dryer with

leaking flexible hoses.

PERSONAL INJURY MAY RESULT.

14. The normal PH level for copper type steam coils

must be

maintained between a value of 8.5 to 9.5. For

steel type steam coils the PH level

must be

maintained between a value of 9.5 to 10.5. These limits are set

to limit the acid attack of the steam coils.

IMPORTANT:

Coil failure due to improper PH level will VOID THE WARRANTY.

15.

READ AND FOLLOW ALL CAUTION AND DIRECTION LABELS ATTACHED TO THE

DRYER.

16. For safety, proper operation, and optimum performance, the dryer

must not be

operated with a load less

than sixty-six percent (66%), 50 pounds (22.67 kg) of its rated capacity.

WARNING: YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND

THE GAS SUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR

GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS

FOR CLEANING, ADJUSTING, INSTALLATION, OR TESTING OF ANY

EQUIPMENT PER OSHA

(Occupational Safety and Health Administration)

STANDARDS.

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды