American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 48

Страница: 48 / 65

WARNING:

When cleaning steam coil fins, be careful not to bend the fins. If fins are bent, straighten

by using a fin comb which is available from local air conditioning supply houses.

90 DAYS

1. Remove lint from around basket (tumbler), drive motors, and surrounding areas.

2. Remove lint from gas valve burner area with a dusting brush or vacuum cleaner attachment.

3. Clean any lint accumulation in and around both the blower and drive motor casing openings.

NOTE:

To prevent damage, avoid cleaning and/or touching ignitor/flame-probe assembly.

EVERY 6 MONTHS

Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryers internal

exhaust ducting.

NOTE: THE ACCUMULATION OF LINT IN THE EXHAUST DUCTWORK CAN

CREATE A POTENTIAL FIRE HAZARD.

NOTE

NOT

OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR.

CHECK CUSTOMER FURNISHED BACK DRAFT DAMPERS IN THE EXHAUST

DUCTWORK. INSPECT AND REMOVE ANY LINT ACCUMULATION, WHICH

CAN CAUSE THE DAMPER TO BIND OR STICK.

NOTE:

A back draft damper that is sticking partially closed can result in slow drying and shutdown of

heat circuit safety switches or thermostats.

NOTE

: When cleaning the dryer cabinet(s), avoid using harsh abrasives. A product intended for the

cleaning of appliances is recommended.

B. ADJUSTMENTS

7 DAYS AFTER INSTALLATION and EVERY 6 MONTHS THEREAFTER

Inspect bolts, nuts, screws, (bearing setscrews), and nonpermanent gas connections (unions, shutoff valves,

orifices, and grounding connections). Motor and drive belts

should be

examined. Cracked or seriously frayed

belts

should be

replaced. Tighten loose V-belts when necessary. Complete operational check of controls and

valves. Complete operational check of

ALL

safety devices (door switches, lint drawer switch, sail switch,

burner and hi-limit thermostats).

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды