American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 34

Страница: 34 / 65

Consistent gas pressure is essential at

ALL

gas connections. It is recommended that a 3/4-inch (19.05

mm) pipe gas loop be installed in the supply line servicing a bank of dryers. An in-line pressure regulator

must be

installed in the gas supply line (header) if the (natural) gas pressure exceeds 12.0 inches (29.9

mb) of water column (W.C.) pressure.

NOTE:

A water column test pressure of 3.5 inches (8.7 mb) for natural gas and 10.5 inches (26.1 mb)

for liquid propane (L.P.) dryers is required at the gas valve pressure tap of each dryer for

proper and safe operation.

An 1/8-inch N.P.T. plugged tap, accessible for a test gauge connection,

must be

installed in the main gas

supply line immediately upstream of each dryer.

IMPORTANT:

Pipe joint compounds that resist the action of natural gas and L.P. gas

must be

used.

IMPORTANT:

Test

ALL

connections for leaks by brushing on a soapy water solution (liquid

detergent works well).

WARNING: NEVER TEST FOR LEAKS WITH A FLAME!!!

ALL

components/materials

must conform

to National Fuel Gas Code Specifications ANSI Z223.1-LATEST

EDITION, or in Canada, CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (L.P. Gas)

or LATEST EDITION (for General Installation and Gas Plumbing), as well as local codes and ordinances

and

must be

done by a qualified professional. It is important that gas pressure regulators meet applicable

pressure requirements, and that gas meters be rated for the total amount of

ALL

the appliance BTUs being

supplied.

IMPORTANT:

The dryer and its individual shutoff valve

must be

disconnected from the gas supply

piping system during any pressure testing of that system at test pressures in excess of

1/2 psig (3.5 kPa).

NOTE

: The dryer

must be

isolated from the gas supply piping system by closing its individual manual

shutoff valve during any pressure test of the gas supply system at test pressures equal to or less

than 1/2 psig (3.5 kPa).

H. STEAM INFORMATION

It is your responsibility to have

ALL

plumbing connections made by a qualified professional to assure that the

steam plumbing installation is adequate and conforms with local and state regulations or codes.

IMPORTANT:

Failure to comply with the requirements stipulated in this manual can result in

component failure, which will VOID THE WARRANTY.

NOTE:

The MLS-75 is manufactured with a pneumatic (piston) damper system, which requires an

external supply of air of 0.75 cfh @ 80 PSI +/- 10 PSI (5.51 bars +/- 0.69) bars.

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды