American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 29

Страница: 29 / 65

3) 3-Phase (3ø) Wiring Connections/Hookup Reversing Models Only

The electrical connections on

ALL

3-phase (3ø) gas and steam dryers are made into the rear

service box located at the upper left area of the dryer. Electrical connections for electrically heated

dryers are made in the electric oven area located at the upper rear area of the dryer.

IMPORTANT:

A separate circuit servicing each dryer

must be

provided.

If local codes permit, power to a gas or steam dryer can be made by the use of a flexible U.L. listed

power cord/pigtail (wire size

must conform

to rating of dryer), or the dryer can be hard wired

directly to the service breaker panel. In

ALL

cases, a strain relief

must be

installed where the

wiring enters the dryer.

The only electrical input connections to the dryer

are the 3-phase (3ø) power leads (L1, L2, L3,

and sometimes neutral) and ground. Single-phase

(1ø) power for the control circuit is done internally

to the dryer. No single-phase (1ø) input

connection is required on a 3-phase (3ø) dryer.

For gas and steam dryers manufactured for operation

at 3-phase (3ø), the electrical connections are made

at the power distribution block located in the service

box at the rear, upper left corner of the dryer. The

ground connection is made to the copper lug also

provided in this box. To gain access to the service

box contactor, the service box cover

must be

removed.

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды