American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 45

Страница: 45 / 65

SECTION V

WARRANTY INFORMATION

A. RETURNING WARRANTY CARDS

1. Before any dryer leaves the

ADC

factory test area, a warranty card is placed on the back side of the main

door glass. These warranty cards are intended to serve the customer where we record the individual

installation date and warranty information to better serve you should you file a warranty claim.

a. If a warranty card did not come with your dryer, contact the

ADC

Warranty Department or the

ADC

Service Department at (508) 678-9000.

IMPORTANT:

A separate warranty card

must be

completed and returned for each individual dryer.

NOTE:

Be sure to include the installation date when returning the warranty card(s).

B. WARRANTY

For a copy of the

ADC

commercial warranty covering your particular dryer(s), contact the

ADC

reseller from

whom you purchased the equipment and request a dryer warranty form. If the reseller

cannot

be contacted or

is unknown, warranty information can be obtained from the factory by contacting the

ADC

Warranty Department

at (508) 678-9000.

NOTE:

Whenever contacting the

ADC

factory for warranty information, be sure to have the dryers

model number

and

serial number

available so that your inquiry can be handled in an

expeditious manner.

C. RETURNING WARRANTY PARTS

ALL

dryer or parts warranty claims or inquires

should be

addressed to the

ADC

Warranty Parts Department.

To expedite processing, the following procedures

must be

followed:

1. No parts are to be returned to

ADC

without prior written authorization (Return Material Authorization

[R.M.A.]) from the factory.

NOTE:

An R.M.A. is valid for only thirty (30) days from date of issue.

a. The R.M.A. issued by the factory, as well as any other correspondence pertaining to the returned

part(s),

must be

included inside the package with the failed merchandise.

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды