American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 31

Страница: 31 / 65

G. GAS INFORMATION

It is your responsibility to have

ALL

plumbing connections made by a qualified professional to assure that the gas

plumbing installation is adequate and conforms to local and state regulations or codes. In the absence of such

codes,

ALL

plumbing connections, materials, and workmanship

must conform

to the applicable requirements of

the National Fuel Gas Code ANSI Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes

CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST

EDITION.

IMPORTANT

: Failure to comply with these codes or ordinances, and/or the requirements stipulated

in this manual, can result in personal injury and improper operation of the dryer.

The dryer and its individual shutoff valves

must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The dryer

must be

isolated

from the gas supply piping system by closing its individual manual shutoff valve during any pressure test of the

gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa).

IMPORTANT:

Failure to isolate or disconnect the dryer from supply as noted can cause irreparable

damage to the gas valve

VOIDING THE WARRANTY.

WARNING: FIRE OR EXPLOSION COULD RESULT.

1. Gas Supply

The gas dryer installation

must meet

the American National Standard...National Fuel Gas Code ANSI

Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes CAN/CGA-B149.1 M91 (Natural

Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION, as well as local codes and ordinances

and

must be

done by a qualified professional.

NOTE:

Undersized gas piping will result in ignition problems, slow drying, increased use of energy, and

can create a safety hazard.

The dryer

must be

connected to the type of heat/gas indicated on the dryer label affixed to the left side

panel/wall area behind the control door. If this information does not agree with the type of gas available,

DO NOT operate the dryer.

Contact the reseller who sold the dryer or contact the

ADC

factory.

IMPORTANT:

Any burner changes or conversions

must be

made by a qualified professional.

The input ratings shown on the dryer data label are for elevations up to 2,000 feet (610 meters), unless

elevation requirements of over 2,000 feet (610 meters) were specified at the time the dryer order was

placed with the factory. The adjustment or conversion of dryers in the field for elevations over 2,000 feet

(610 meters) are made by changing each burner orifice. If this conversion is necessary, contact the

reseller who sold the dryer or contact the

ADC

factory.

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды