American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 42

Страница: 42 / 65

10. Reversing Models Only - Basket (tumbler) dryer

should never be

operated with less than a 30 lb. (14 kg)

load dry weight. The size of the load will affect the coast-down and dwell (stop)

times. The basket (tumbler) must come to a complete stop before starting in

opposite direction.

a. Microprocessor Models

1) Spin and stop are not adjustable in the Automatic Mode and have been preprogrammed into the

microprocessor controller (computer) for 150-seconds spin time in forward direction, 120-seconds

in the reverse direction and a 5-second dwell (stop) time.

2) Spin and stop times are adjustable in the Manual (timed) Mode.

b. Dual Timer Models

1) Both dwell (stop) and basket (tumbler) spin time are adjustable. (Refer to the

illustration

page

11. Check to insure that

ALL

setscrews (i.e., basket [tumbler] drive, idler, etc.) are tight.

K. PREOPERATIONAL INSTRUCTIONS

1. To start the dryer:

a. Microprocessor Controller (Computer) Dryers...

1) Light emitting diode (L.E.D.) display will read REAdY (meaning no cycle in progress).

2) Press the letter on the keyboard (touch pad) corresponding to the cycle desired (i.e., key E)...

a) The dryer will then start (rotate).

3) L.E.D. display will now show Cycle In Progress and Cycle Status meaning that the dryer is in

the drying cycle (dry mode for 30 minutes) and count downwards in minutes.

NOTE:

Pressing keyboard (touch pad) key A B C D, and F will also start the dryer. The six

(6) preprogrammed drying cycles A through F) have been stored in the microprocessor

controller (computer) memory. Refer to the Programming Manual supplied with the dryer for

more specific operating instructions.

NOTE:

The dryer can be stopped at any time by opening the main door or by pressing the STOP

red key. To restart the dryer, press the START green key or a preprogrammed cycle key

(i.e., E).

NOTE:

Selection (settings) changes can be made at any time during the drying cycle by pressing the

STOP red key twice. The L.E.D. display will return to REAdY at which time a new cycle

selection can be made.

b. Dual Timer Dryers

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды