American Dryer Corp. ML-75DIII Скачать руководство пользователя страница 16

Страница: 16 / 65

C. DRYER ENCLOSURE REQUIREMENTS

Bulkheads and partitions

should be

made of noncombustible materials and

must be

located a minimum of

12-inches (30.48 cm), 18-inches (45.72 cm) or more is recommended for ease of installation, maintenance, and

service above the dryer outer top, except along the front of the dryer which may be partially closed in if desired.

The clearance between the bulkhead header and the dryer

must be

a minimum of 4-inches (10.16 cm) and

must not

extend more than 4-inches (10.16 cm) to the rear of the front. The bulkhead facing

must not

closed in

ALL

the way to the top of the dryer. A 1-inch (2.54 cm) clearance is required.

NOTE

: Allowances

must be

made for opening the control door.

Dryers may be positioned sidewall to sidewall. However, a 1/16-inch (1.5875 mm) minimum allowance

must be

made for the opening and closing of the control door and the lint door. It is suggested that the dryer be positioned

about 30-inches (76.2 cm) away from the nearest obstruction for ease of installation, maintenance, and service

(to be measured from the back guard.) Refer to the

illustration above

for details.

NOTE:

Air considerations are important for proper and efficient operation.

IMPORTANT:

For overhead clearance, even though a minimum of only 12-inches (30.48 cm) is

required, 18-inches (45.72 cm) or more is suggested. The additional clearance is

advantageous for ease of installation and service.

IMPORTANT:

When fire sprinkler systems are located above the dryers, a minimum of 18-inches

(45.72 cm) above the dryer console (module) is required. Dryers may be positioned

sidewall to sidewall however, a 1/16-inch (1.5875 mm) minimum allowance is

required between dryers (or wall) for ease of installation and maintenance.

Allowances

must be

made for the opening and closing of the control door and the lint

door.

Содержание ML-75DIII


































































Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды

American Dryer Corp. ML-75DIII, Руководство по установке

Результаты поиска

Содержание ML-75DIII

Отзывы:

Похожие инструкции для ML-75DIII

Бренды по названию

Популярные бренды