Alvarado CLSTT-3 Скачать руководство пользователя

Страница: 42 / 46

Full Height Tandem Installation Instructions

Page 42 [email protected] +1(909) 591-8431 www.alvaradomfg.com

Installation Instructions

Appendix C -

Fail-lock / Fail-safe Spring and Solenoid Configurations (Cont)

Fail-safe

Fail-lock

Clockwise

Fail-lock / Fail-safe Spring and Solenoid Configurations - Fixed

Solenoid

NOTE

For use with turnstiles that utilize fixed solenoid mounting positions.

NOTE

Bend lock arm tabs to mechanically adjust spring tension.

Increase

spring

tension

Decrease

spring

tension

Increase

spring

tension

Decrease

spring

tension

A - Return Spring
B - Solenoid

Spring

CCW

Lock Arm

Fail-safe

Solenoid

Fail-lock

Solenoid

A - Return

Spring
B - Solenoid

Spring

(Black)

(Red)

(Black)

(Silver)

CCW

Lock Arm

4 3

211

Spring Configuration

Solenoid Mount Position

Spring Configuration

Solenoid Mount Position (use holes 2 & 4)

Содержание CLSTT-3















































Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды

Alvarado CLSTT-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды