Alvarado CLSTT-3 Скачать руководство пользователя

Страница: 2 / 46

Full Height Tandem Installation Instructions

Page 2 [email protected] +1(909) 591-8431 www.alvaradomfg.com

Installation Instructions

Contents

Contents. ......................................................................................................................................................................... 2

Safety Precautions. ......................................................................................................................................................... 3

Safety Icons. .................................................................................................................................................................... 3

Compliance and Standards. ............................................................................................................................................ 4

Installation Tools. ............................................................................................................................................................. 4

Parts List.......................................................................................................................................................................... 5

Before You Begin. ............................................................................................................................................................ 6

Common Terms. .............................................................................................................................................................. 6

Installation Instructions. ................................................................................................................................................... 7

Installation Locations. ............................................................................................................................................... 7

Bottom Bearing Plate Installation. ............................................................................................................................. 8

Yoke Installation . ...................................................................................................................................................... 9

Roto Installation. ............................................................................................................................................................ 10

Top Channel Installation. ................................................................................................................................................11

OV Installation. .............................................................................................................................................................. 12

Guard Plate Installation. ................................................................................................................................................ 15

Bearing Cover Installation. ............................................................................................................................................ 15

Top Bearing Cover Installation . .............................................................................................................................. 15

Bottom Bearing Cover Installation . ........................................................................................................................ 15

Final Mechanical Installation Steps. .............................................................................................................................. 16

Key Override Operation. ................................................................................................................................................ 16

Conduit Instructions. ...................................................................................................................................................... 17

Electrical Wiring Instructions. ........................................................................................................................................ 18

Turnstile Control Board Layout. .............................................................................................................................. 19

Terminal Descriptions. ............................................................................................................................................. 20

SW4 DIP Switch Descriptions. ................................................................................................................................ 22

User Activation and Passage Instructions. .................................................................................................................... 23

Post-Installation Checklist. ............................................................................................................................................ 24

Troubleshooting. ............................................................................................................................................................ 25

Cleaning and Maintenance. ........................................................................................................................................... 30

Lubrication. .................................................................................................................................................................... 32

Appendix A - CPSTT Installation. .................................................................................................................................. 34

Yoke Installation. ..................................................................................................................................................... 35

Appendix B - CLSTT Installation. .................................................................................................................................. 38

Appendix C -

Fail-lock / Fail-safe Spring and Solenoid Configurations.

........................................................................ 39

Clockwise. ............................................................................................................................................................... 39

Fail-safe. ................................................................................................................................................................. 39

Fail-lock. .................................................................................................................................................................. 39

Appendix D - Key Override Adjustable Cam Installation. .............................................................................................. 43

Clockwise. ............................................................................................................................................................... 43

Counter-Clockwise. ................................................................................................................................................. 44

Revision History. ............................................................................................................................................................ 45

Содержание CLSTT-3















































Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды

Alvarado CLSTT-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды