Alvarado CLSTT-3 Скачать руководство пользователя

Страница: 34 / 46

Page 34 [email protected] +1(909) 591-8431 www.alvaradomfg.com

Installation Instructions

Turnstile

Center

Turnstile

Center

Appendix A - CPSTT Installation

Determine where the turnstile will be

installed. Consider the overall

footprint size of the unit when

determining the installation location

(Figure A1). Once the installation

location has been determined, use a

chalk line to mark the centerline of

the turnstile.

Default entry rotation is counter-clockwise.

Confirm correct entry direction prior to

installation.

Yoke

(Qty 2)

Roto

(Qty 2)

(Qty 1)

CPSTT Illustrated Parts List

Yoke Mounting

Channel - Lower

(Qty 8)

#10 x 3/4" Mounting

Screws (Qty 20)

These instructions are for installing the Yoke section of the CPSTT. When complete, please refer back to the "Roto

Installation" section.

Fig. A1

CPSTT Installation Instructions

NOTE

The overall height of the CPSTT is 91.5".

However, an additional 3" of clearance must

be added for service and maintenance.

Yoke Half

Section

Roto

Centerline

Yoke

Centerline

Yoke

Centerline

94.50"

47.25"

Roto

Centerline

29.63"

33.00"

Yoke Half

Section

8.00"

16.50"

54"

Fig. A2

Yoke Lower Mounting Channel Installation

Determine the installation location for the Yoke.

Identify the threaded aluminum block is at the top

of each section. (Figure A2).

Push the two sections together (Figure A2).

NOTE

Prior to drilling the anchor bolt holes, use a tape

measure and measure the distance from the bottom

bearing plate center to the outer mounting holes on

the two Yoke sections (Figure A1). Adjust the Yoke

until these two distances are identical. Mark these two

locations.

Threaded

Aluminum Block

Yoke Section

Yoke Mounting

Channel - Upper

(Qty 8)

1/4-20 x 1" Mounting

Screws (Qty 12)

Содержание CLSTT-3















































Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды

Alvarado CLSTT-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды