Alvarado CLSTT-3 Скачать руководство пользователя

Страница: 37 / 46

Installation Instructions [email protected] +1(909) 591-8431 www.alvaradomfg.com

Page 37

CLSTT Installation Instructions

Yoke Installation (Cont)

Yoke Upper Mounting Channel Installation

Place each upper mounting channel inside the Yoke

upper channel (Figure A9). Align mounting channel

with the pre-drilled hole (Figure A9 - Inset) .

Use a 9/64" drill bit and pre-drill a mounting hole

into the center of each upper mounting channel.

Secure each upper mounting channel to the Yoke

using a ¼-20 x 1” screw (Figure A9-Inset).

Tighten each screw using a Phillips head

screwdriver.
6.

Repeat Steps 1 through 5 for the second Yoke

installation.

NOTE

For the CPSTT, the Roto with 11 arms must be installed

on the right side (as viewed from the unsecured/entry

side) and the Roto with 10 arms must installed on the left

side (Figure A10).

When complete, continue on to the "Roto Installation"

section.

10 Arms

11 Arms

Fig. A10

Fig. A9

Yoke Assembly

Upper Mounting Channel

¼-20 x 1" Screw

Upper Mounting

Channel

Pre-drilled Hole

Upper Channel

A9 Inset

Содержание CLSTT-3















































Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды

Alvarado CLSTT-3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CLSTT-3

Отзывы:

Похожие инструкции для CLSTT-3

Бренды по названию

Популярные бренды