Alvarado CLSTT-3 Скачать руководство пользователя | Manualshive

Страница: 12 / 46

background image

Full Height Tandem Installation Instructions

Page 12 [email protected] +1(909) 591-8431 www.alvaradomfg.com

Installation Instructions

Top Channel Installation (Cont)

Fig. 15

7.

The Top Channel mounting holes are located at each end of the Top Channel (Figure 15).

A. Yoke - Insert four ½" x 2¾" hex head bolts, from the underside of the Top Channel, up through the mounting

holes and secure with four ½" lock washers and four ½" nuts (Figure 15A).

8.

Hand tighten the Top Channel mounting hardware at this time.

Fig. 16

13 Rungs

12 Rungs

As viewed from the unsecured/entry side.

NOTE

For MSTT and CLSTT models, the OV must

be installed with 12 rungs facing the right side

and 13 rungs the left side (as viewed from the

unsecured/entry side; Figure 16).

For the CPSTT, the OV must be installed

with 10 rungs facing the right side and 11

rungs facing the left side (as viewed from the

unsecured/entry side; Figure 16).

11 Rungs

10 Rungs

MSTT / CLSTT

CPSTT

OV Installation

15A

«
...
10
11
12
13
14
...
»

Содержание CLSTT-3















































Отзывы:

Нет отзывов

Похожие инструкции для CLSTT-3

Бренд: ZKTeco Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды