manualshive.com logo in svg

Altigen MAX Communication Server ACC 6.0, Руководство администратора

Административное руководство для Altigen MAX Communication Server ACC 6.0 доступно для загрузки бесплатно на нашем сайте. Это удобное пособие позволит вам освоить все возможности этого продукта. Не упустите возможность скачать его с manualshive.com.

Поделиться
Скачать
background image

Chapter 1:  Overview

16

MAXCS ACC 6.0 Administration Manual

Global IP Dialing Table 

- The IP Dialing Table is configured in Enterprise Manager. The 

IP Dialing Table configuration is used to create location-based routing in the Enterprise. 

H.323 Tie-Trunk Support 

- Ensures backward compatibility to systems using AltiGen’s 

AltiWare versions prior to 5.1. 

IP Extension Auto Failover

 - when an IP extension is unreachable, the system will 

automatically fail over to a pre-configured Mobile Extension.

IP Group Paging

 - allows the use of voice paging to IP phone users in a group.

NAT Configuration for SIP/H.323

 - When AltiServ is behind NAT with a private IP 

address, this feature helps to resolve IP address resolution problems when 

communicating with an external VoIP device.

Silence Detection

 and 

Suppression

 - when silence suppression is enabled and silence 

is detected, the system stops sending packets to the other side. The other side does not 
receive any packets and plays silence.

VoIP Hop-Off Call Support

 - allows an extension to access a PSTN trunk on the remote 

system and “hop off” to dial an outside telephone number. This hop off feature can be 
enabled or disabled on the remote system. Outcall restrictions for hop off calls are 
configurable.

SIP Trunk Support

 - MAXCS enables AltiGen’s system to connect to IP-based trunking 

service providers via SIP. 

SIP NAT Traversal 

- Allows MAXCS to connect to a remote SIP phone or IPTalk behind 

NAT without changing the NAT setting at the remote location.

Support for RFC 2833 (DTMF payload embedded with RTP)

 - Supported in SIP 

trunks only. This feature helps to resolve DTMF tone detection and regeneration when 

using G.723.1 or G.729 codec. Basically low bit rate compression will distort DTMF tone 
during compression. The far end device may not be able to recognize the DTMF digits. 
RFC 2833 specifies a separate RTP payload format to carry DTMF information to ensure 

the other side can recognize the tone properly.

Support for both SIP and H.323 Tie Trunk

 - When setting up a system-to-system 

VoIP tie trunk, either SIP or H.323 protocol can be used.

Multi-Site VoIP Management - Enterprise Manager

Multi-site management through Enterprise Manager includes:

VoIP domain 

- when networking multiple AltiGen systems from different sites, one 

system can be assigned as VoIP domain controller to propagate configuration data to 
member systems.

Directory Synchronization

 - when a new extension is added to one of the member 

systems and configured as Global extension, the VoIP domain controller will propagate 

this extension to all member systems. Every member system within the VoIP domain will 
be able to see the extension number plan of other systems.

Multi-site Call Routing

 - when a user dials an extension number that is not a local 

extension number, the system will search the Domain extension list. If a list is found, 

the system will dial the number by using the IP address and extension number stored in 
the Domain extension list.

Domain User Management

 - The VoIP domain controller can resolve the conflict if 

duplicated extension numbers are created in different member systems. This feature 

also manages extension relocation. When an extension user is relocated to another 
member system, its voice mail and greeting can be moved along with it.

Содержание MAX Communication Server ACC 6.0






































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAX Communication Server ACC 6.0

Canon PowerShot A530 Software User'S Manual preview
PowerShot A530
Бренд: Canon Страницы: 153
Canon PowerShot A420 Software User'S Manual preview
PowerShot A420
Бренд: Canon Страницы: 132
Canon PowerShot A460 Using Manual preview
PowerShot A460
Бренд: Canon Страницы: 135
Canon MultiPASS C50 Software User'S Manual preview
MultiPASS C50
Бренд: Canon Страницы: 198
Canon PowerShot A530 Software Starter Manual preview
PowerShot A530
Бренд: Canon Страницы: 98
FARONICS DEVICE FILTER MAC Manual preview
DEVICE FILTER MAC
Бренд: FARONICS Страницы: 30
Mustek 1200 CP User Manual preview
1200 CP
Бренд: Mustek Страницы: 28
Red Hat ENTERPRISE LINUX 3 - SECURITY GUIDE Manual preview
ENTERPRISE LINUX 3 - SECURITY GUIDE
Бренд: Red Hat Страницы: 410
Yamaha YC-3B Installation Manual preview
YC-3B
Бренд: Yamaha Страницы: 4
Yamaha YC-3B Owner'S Manual preview
YC-3B
Бренд: Yamaha Страницы: 6
Yamaha USB Installation Manual preview
USB
Бренд: Yamaha Страницы: 7
Yamaha Studio Manager v.2 Owner'S Manual preview
Studio Manager v.2
Бренд: Yamaha Страницы: 11
Yamaha Studio Manager v.2 Installation Manual preview
Studio Manager v.2
Бренд: Yamaha Страницы: 15
Yamaha VL Visual Editor Manual preview
VL Visual Editor
Бренд: Yamaha Страницы: 23
Yamaha TOOLS for MY16-mLAN Owner'S Manual preview
TOOLS for MY16-mLAN
Бренд: Yamaha Страницы: 24
Yamaha TOOLS for TYROS Installation Manual preview
TOOLS for TYROS
Бренд: Yamaha Страницы: 36
Acroprint TimeStation PC Quick Start Manual preview
TimeStation PC
Бренд: Acroprint Страницы: 2
3Com SUPERSTACK 3 WEBCACHE 3000 User Manual preview
SUPERSTACK 3 WEBCACHE 3000
Бренд: 3Com Страницы: 362

Бренды по названию

Популярные бренды

Загрузить еще бренды