Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 71

Страница: 71 / 116

Publication 1769-UM005A-EN-P

Module Data, Status, and Channel Configuration

4-31

Calculating Module Update Time with Cyclic Lead Wire
Compensation Enabled

The following example illustrates how to determine module update time
with cyclic lead wire compensation enabled.

EXAMPLE

Two Channels Configured with Cyclic Lead Wire Compensation Enabled

Channel 0 Input: 100

Ω

Platinum 385 with 60 Hz Filter (use 60 Hz filter for lead wire)

Channel 1 Input: 100

Ω

Platinum 385 with 250 Hz Filter (use 250 Hz filter for lead wire)

From Table 4.15, Channel Update Time vs. Filter Frequency, on page 4-26:

1. Calculate Module Update Time

without

a Lead Wire Compensation Cycle

= Ch 0 Update Time + Ch 1 Update Time = 53 ms + 15 ms = 68 ms

2. Calculate Module Update Time

during

a Lead Wire Compensation Cycle

Channel 0 Scan 1 (Module Scan 1)

Ch 0 Update Time +

Ch 0 Lead Wire Compensation Time

+ Ch 1 Update Time

= 53 ms +

ms + 15 ms = 121 ms

The above module update time impact lasts for two more module scans, before the lead-wire
compensation cycle is complete for Channel 0:

Channel 0 Lead Wire Compensation Cycle Time

= (3 x 121 ms) = 363 ms.

After that, a 3-scan lead wire cycle begins for Channel 1:

Channel 1 Scan 1 (Module Scan 4)

= Ch 0 Update Time + Ch 1 Update Time +

Ch 1 Lead Wire Compensation Time

= 53 ms + 15 ms +

ms = 83 ms

The above module update time impact lasts for two more module scans, before the lead-wire
compensation cycle is complete for Channel 1:

Channel 1 Lead Wire Compensation Cycle Time

= (3 x 83 ms) = 249 ms.

3. Calculate Total Time to Complete Lead Wire Compensation Cycle

= (Ch 0 Lead Wire Compensation Cycle Time) + (Ch 1 Lead Wire Compensation Cycle Time)
= (363 ms) + (249 ms)
= 612 ms = 0.612 seconds

After the above cycles are complete, the module returns to scans without lead wire compensation
for approximately 5 minutes. At that time, the lead wire compensation cycle repeats.

If both cyclic autocalibration (see page 4-27) and lead wire compensation are enabled, the two
functions run concurrent to one another.

AB PLCs

Содержание Compact 1769-IR6





















































































































Результаты поиска

Содержание Compact 1769-IR6

Отзывы:

Похожие инструкции для Compact 1769-IR6

Бренды по названию

Популярные бренды

Allen-Bradley Compact 1769-IR6, Руководство пользователя

Результаты поиска

Содержание Compact 1769-IR6

Отзывы:

Похожие инструкции для Compact 1769-IR6

Бренды по названию

Популярные бренды