Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 116

background image

Publication 1769-UM005A-EN-P

3-2

Installation and Wiring

Power Requirements

The module re5V dc and 24V dc power from the system power
supply through the CompactBus interface.

The maximum current drawn by the module is shown in the table below.

General Considerations

Compact I/O is suitable for use in an industrial environment when
installed in accordance with these instructions. Specifically, this
equipment is intended for use in clean, dry environments (Pollution

degree 2

(1)

) and to circuits not exceeding Over Voltage Category II

(2)

(IEC

60664-1).

(3)

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D
or non-hazardous locations only. The following WARNING statement
applies to use in hazardous locations.

5V dc

24V dc

100 mA

45 mA

NOTE

When you configure your system, ensure that the total
current draw of all the modules does not exceed the
maximum current output of the system power supply.

(1) Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a

temporary conductivity caused by condensation shall be expected.

(2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages

are controlled and do not exceed the impulse voltage capability of the product’s insulation.

(3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.

WARNING

!

EXPLOSION HAZARD

•

Substitution of components may impair suitability for
Class I, Division 2.

•

Do not replace components or disconnect equipment
unless power has been switched off or the area is
known to be non-hazardous.

•

Do not connect or disconnect components unless
power has been switched off or the area is known to
be non-hazardous.

•

This product must be installed in an enclosure.

•

All wiring must comply with N.E.C. article 501-4(b).

«
...
24
25
26
27
28
...
»

Содержание Compact 1769-IR6





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact 1769-IR6

Бренд: IBM Страницы: 72

Бренд: National Instruments Страницы: 9

Бренд: QUALITY LIFTS Страницы: 21

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

Бренд: Skytec Страницы: 12

Бренд: Innovative Technology Страницы: 14

Бренд: K-Systems Страницы: 9

Бренд: Ravaglioli Страницы: 102

Бренд: Konig Security Страницы: 92

Бренд: Commax Страницы: 11

Бренд: Autopot Страницы: 2

Бренд: Jet Страницы: 16

Бренд: Contec Страницы: 62

Бренд: Alcad Страницы: 28

Бренд: Technics Страницы: 14

Бренд: Eaton Страницы: 8

Бренд: CMC Страницы: 77

Бренд: WaterGroup Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды