Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 116

background image

Publication 1769-UM005A-EN-P

Specifications

A-3

Specification

1769-IR6

Accuracy Drift at 0 to 60° C (+32 to
+140°F)

±0.026°C/°C (0.026°F/°F) for Pt 385
±0.023°C/°C (0.023°F/°F) for Pt 3916
±0.012°C/°C (0.012°F/°F) for Ni
±0.015°C/°C (0.015°F/°F) for NiFe
±0.032°C/°C (0.032°F/°F) for Cu

±0.007

Ω

/°C (0.012

Ω

/°F) for 150

Ω

range

±0.023

Ω

/°C (0.041

Ω

/°F) for 500

Ω

range

±0.043

Ω

/°C (0.077

Ω

/°F) for 1000

Ω

range

±0.072

Ω

/°C (0.130

Ω

/°F) for 3000

Ω

range

Repeatability

(1)

±0.1°C (±0.18°F) for Ni and NiFe
±0.2°C (±0.36°F) to ±0.2°C (±0.36°F) for other RTD inputs
±0.04

Ω

for 150

Ω

resistances

±0.2

Ω

for other resistances

Excitation Current Source

0.5 mA and 1.0 mA selectable per channel

Open-Circuit Detection Time

(2)

6 to 303 ms. Open-circuit detection time equals Channel update time. See Determining Module
Update Time on page 4-26.

Channel Update Time

Input filter and configuration dependent.

Input Channel Configuration

via configuration software screen or the user program (by writing a unique bit pattern into the
module’s configuration file). Refer to your controller’s user manual to determine if user program
configuration is supported.

Calibration

The module performs autocalibration on channel enable and on a configuration change between
channels. You can also program the module to calibrate every five minutes.

Module OK LED

On: module has power, has passed internal diagnostics, and is communicating over the bus.
Off: Any of the above is not true.

Channel Diagnostics

Over- or under-range or broken input by bit reporting

Maximum Overload at Input Terminals

Voltage: ±30V dc continuous, 50 mA
Current: ±50 mA continuous, ±30V dc

Cable Impedance Max.

25

Ω (

Operating with >25

Ω

will reduce accuracy.)

Input Impedance

>10 M

Ω

Power Supply Distance Rating

8 (The module may not be more than 8 modules away from the system power supply.)

Channel to Bus Isolation

720V dc for 1 minute, optical and magnetic (qualification test)
30V ac/30V dc working voltage (IEC Class 2 reinforced insulation)

Channel to Channel Isolation

±10V dc

Vendor I.D. Code

1

Product Type Code

10

Product Code

37

(1) Repeatability is the ability of the module to register the same reading in successive measurements for the same input signal.

(2) Open-circuit detection time is equal to channel update time.

«
...
83
84
85
86
87
...
»

Содержание Compact 1769-IR6





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact 1769-IR6

Spacemaker 7-5400

Бренд: GE Страницы: 12

Бренд: GE Страницы: 36

Бренд: Handicare Страницы: 32

Бренд: abc Страницы: 8

Бренд: Ace Страницы: 13

Бренд: bar Страницы: 2

Бренд: Fanvil Страницы: 6

Бренд: National Instruments Страницы: 9

Бренд: Balboa Страницы: 23

Бренд: Panasonic Страницы: 89

Бренд: GE Страницы: 28

Бренд: Rain Bird Страницы: 2

Бренд: Valx Страницы: 28

i-Kiosk 100 Plus

Бренд: FingerTec Страницы: 3

Бренд: Skyjack Страницы: 47

Бренд: claber Страницы: 21

Бренд: Yabang Страницы: 6

Бренд: National Instruments Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды