Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 20

Страница: 20 / 116

Publication 1769-UM005A-EN-P

2-2

Quick Start for Experienced Users

The modules maximum current draw is shown below.

(1) The system power supply could be a 1769-PA2, -PB2, -PA4, -PB4, or the internal power supply of a MicroLogix 1500

packaged controller.

Check that the bus lever of the module to be installed is in the
unlocked (fully right) position.

Use the upper and lower tongue-and-groove slots (1) to secure the
modules together (or to a controller).

Step 1: Ensure that your 1769 system power supply

(1)

has sufficient current output to support your
system configuration.

Reference

Chapter 3
(Installation and Wiring)

5V dc

24V dc

100 mA

45 mA

NOTE

The module cannot be located more than 8 modules
away from the 1769 system power supply.

Step 2: Attach and lock the module.

Reference

Chapter 3
(Installation and Wiring)

NOTE

The modules can be panel or DIN rail mounted. Modules
can be assembled before or after mounting.

ATTENTION

Remove power before removing or inserting this module.
When you remove or insert a module with power
applied, an electrical arc may occur.

Содержание Compact 1769-IR6





















































































































Результаты поиска

Содержание Compact 1769-IR6

Отзывы:

Похожие инструкции для Compact 1769-IR6

Бренды по названию

Популярные бренды

Allen-Bradley Compact 1769-IR6, Руководство пользователя

Результаты поиска

Содержание Compact 1769-IR6

Отзывы:

Похожие инструкции для Compact 1769-IR6

Бренды по названию

Популярные бренды