background image

7

7.  Battery Safety

Burn Hazards

CAUTION

• The battery fluid contains corrosive acid. 

When dealing with the battery, always 
wear appropriate protective clothing and 
equipment to protect your hands, eyes, 
face and body, and avoid contacting 
battery fluid.

• If battery fluid gets on the skin or on 

clothing, wash it away immediately with 
cold water. If it gets into the eye, wash 
immediately with cold water, and seek 
medical treatment immediately.

Explosion Hazards

WARNING

• The battery produces flammable hydrogen 

gas, and there is a possibility of explosion. 
Never allow anything that can cause fire to 
be close to the battery. Charge the battery 
only under good ventilation.

• If the electrolyte is frozen, slowly warm the 

battery before you recharge it.

8.  Engine Safety

Scald Hazards

WARNING

• Never remove the radiator cap if the 

engine is hot. Steam and hot engine 
coolant will spurt out and seriously burn 
you. Allow the engine to cool down before 
you attempt to remove the radiator cap.

• Tighten the radiator cap securely after you 

check the radiator. Steam can spurt out 
during engine operation if the cap is loose.

• Keep your hands and other body parts 

away from hot components, such as 
the muffler and exhaust pipe, during 
operation and shortly after shutdown. 
These components are extremely hot 
while the engine is operating and could 
seriously burn you.

Exhaust Hazard

WARNING

• Never operate the machine in an 

enclosed area such as a garage, tunnel, 
or underground room without proper 
ventilation.

• Never block windows, vents, or other 

means of ventilation if the machine is 
operating in an enclosed area. The engine 
creates carbon monoxide gas during 
operation. Accumulation of this gas within 
an enclosure could cause illness or even 
death.

Coolant Hazard

CAUTION

  Wear eye protector and rubber gloves 

when you handle long life or extended life 
engine coolant. If contact with the eyes 
or skin should occur, flush eyes and wash 
immediately with clean water.

9.  Personal Safety

Fall Hazards

DANGER

• Always use a safety harness in the 

platform. All persons in the platform 
must comply with employer, work area, 
and local and national safety regulations 
regarding the use of personal protective 
equipment.

• All personal fall protective equipment 

must be attached to only the 
authorized lanyard anchorage 
points provided in the 
platform.

WARNING

  All personal protective equipment must 

comply with applicable regulations, and 
must be inspected and used in accordance 
with the manufacturerʼs instructions.

Содержание SR12CSM















































































Отзывы: