Aichi SR12CSM Скачать руководство пользователя страница 34

Страница: 34 / 78

WARNING

Do not move the machine to the

workplace until the workplace check is
performed.

• Make sure to check the workplace before

starting operation. Make sure there are no
following hazards:

- Near electric power lines and apparatus
- Drop-offs or holes, including those concealed

by water, ice, mud, etc.

-  Slope(s)
-  Slippery or icy surfaces
-  Inadequate surface support to withstand all

load forces imposed by the machine in all
operating configurations

- Bumps and floor obstructions and electrical

conductors

-  Curbs
-  Debris
-  Overhead obstructions
-  Wind and weather conditions
-  Dark workplace (night work)
-  Hazardous locations and atmospheres
-  Presence of unauthorized persons
-  Other possible unsafe conditions

• Remove the hazards, if any, after the workplace

check. If it is not possible to remove them, do
not move the machine to the workplace.

• The machine can be used only on surfaces

which are firm and for which all both tracks can
maintain contact evenly with the ground.

• During work, always pay attention to

surroundings and make sure there is no hazard.

• To prevent collision, place warning signs,

indicate detours and install collision-prevention
guards around the workplace, so that
pedestrian and cars can pass safely.

Workplace Check

Содержание SR12CSM















































































Результаты поиска

Содержание SR12CSM

Отзывы:

Похожие инструкции для SR12CSM

Бренды по названию

Популярные бренды

Aichi SR12CSM, Руководство по эксплуатации с информацией по обслуживанию

Результаты поиска

Содержание SR12CSM

Отзывы:

Похожие инструкции для SR12CSM

Бренды по названию

Популярные бренды