Aichi SR12CSM Скачать руководство пользователя страница 68

Страница: 68 / 78

2. General Specifications

Commercial Name / Model Code

SR12CSM / SR12C1SM

Platform Height Maximum

12.1 m

Horizontal Outreach Maximum

10.7 m

Platform Load Capacity (Evenly Distributed)

250 kg or 2 p tools: 90 kg

Platform Rotation

[P] 90°

CW ‒ 90°

CCW (180°

)

Turntable Rotation

360°

(Continuous)

Max. Allowable Tilt Angle

5°

Gradeability*

(Stowed)

58 % (30°

)

Min. Turning Radius

[C] 1.74 m

Max. Allowable Wind Speed

12.5 m/s

Max. Allowable Manual Side Force

400 N (41 kgf)

Overall Length

[X] 6.32 m

Overall Width

[Y] 2.30 m

Overall Height

[Z] 1.995 m

Turntable Tail Swing Radius

[R] 1.75 m

Turntable Tail Swing

[S] 600 mm

Inside Diameter of Platform

[LWD] 0.75 x 1.80 x 1.11 m

Track Width

[T] 450 mm

Width of Tumbler Center

[B] 2.045 m

Width of Crawler Center

1.85 m

Ground Clearance

[G] 340 mm

Gross Weight

7,550 kg

Max. Track Loading Force

6,125 kg

Max. Track Ground Contact Pressure

65 kPa

r sou

Engine

YANMER 3TNV88

Auxiliary Power Unit

12V-DC

Fuel Type

Diesel Fuel (Ultra Low Sulfur -limited)

Fuel Tank Capacity

95 L

Recommended Hydraulic Oil

Shell Tellus S2 M 22

Hydraulic Tank Capacity

145 L

peed

Elevation
(Retracted Fully)

-19 ‒ 70°

/ 44 ‒ 56 s

Down

-19 ‒ 70°

/ 44 ‒ 56 s

Telescope

Out

6.11 m / 20 ‒ 30 s

Turntable Rotation (Retracted and Raised Fully)

0.54 rpm (360°

/ 98 ‒ 122 s)

Platform Rotation

180°

/ 9 ‒ 17 s

Max. Travel Speed*

(Level Surface)

Stowed

1.5 km/h

Elevated

0.9 km/h

• The machine is designed for both indoor and outdoor use.
• Advisable atmospheric temperature range: -20 ℃ ‒ +40 ℃
*

Function speeds and gradeability assume there is 1 person on the machine.

Travel speed and gradeability depend on the condition of the traveling surface.

Weight information is approximate and does not incorporate different option configurations.

Содержание SR12CSM















































































Результаты поиска

Содержание SR12CSM

Отзывы:

Похожие инструкции для SR12CSM

Бренды по названию

Популярные бренды

Aichi SR12CSM, Руководство по эксплуатации с информацией по обслуживанию

Результаты поиска

Содержание SR12CSM

Отзывы:

Похожие инструкции для SR12CSM

Бренды по названию

Популярные бренды